LTC6244CMS8#PBF

1pA 105 dB Instrumentational OP Amps 0.000075μA 2.8V~6V LTC6244 8 Pins 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)

Manufacturer: Linear Technology/Analog Devices
Nocochips NO: 471-LTC6244CMS8#PBF
Package: 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
Datasheet: PDF
Stock: 781
Description: 1pA 105 dB Instrumentational OP Amps 0.000075μA 2.8V~6V LTC6244 8 Pins 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mounting Type	Surface Mount
Package / Case	8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
Surface Mount	YES
Operating Temperature	0°C~70°C
Packaging	Tube
Published	2009
JESD-609 Code	e3
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
ECCN Code	EAR99
Terminal Finish	Matte Tin (Sn)
Subcategory	Operational Amplifier
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	5V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	LTC6244
Pin Count	8
JESD-30 Code	S-PDSO-G8
Qualification Status	Not Qualified
Output Type	Rail-to-Rail
Power Supplies	3/5V
Number of Circuits	2
Current - Supply	6.25mA
Slew Rate	35V/μs
Architecture	VOLTAGE-FEEDBACK
Amplifier Type	General Purpose
Common Mode Rejection Ratio	105 dB
Current - Input Bias	1pA
Voltage - Supply, Single/Dual (±)	2.8V~6V
Gain Bandwidth Product	50MHz
Unity Gain BW-Nom	50000 kHz
Average Bias Current-Max (IIB)	0.000075μA
Low-Offset	YES
Frequency Compensation	YES
Supply Voltage Limit-Max	7V
Voltage - Input Offset	40μV
Current - Output / Channel	35mA
Low-Bias	YES
Micropower	NO
Programmable Power	NO
Wideband	NO
Power	NO
Voltage Gain-Min	100000
Height Seated (Max)	1.1mm
Length	3mm
RoHS Status	ROHS3 Compliant

LTC6244CMS8#PBF Overview

The linear amplifier is packaged in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case. An op amp ic of the General Purpose type. Instrumentation amplifier is delivered in a Tube case. There is a growing number of terminations approaching the number of 8. A total of 8 pins are located on this board. I would like to remind you that this buffer op amp should be powered by an 5V battery. It should be noted that this op amp is a type of Operational Amplifier device. For this electronic part, it is recommended that you mount it with type Surface Mount. The buffer amplifier functions well at 0°C~70°C as far as operating temperature is concerned. The buffer amp consists of 2 circuits in total. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. It is recommended that this electronic component be used with an 6.25mA supply. A minimum voltage gain of 100000 is the minimum voltage gain that this instrumentation amplifier is capable of producing.