LTC6244HVHDD#PBF
| Parameters | |
|---|---|
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-WFDFN Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | LTC6244 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Circuits | 2 |
| Operating Supply Current | 7mA |
| Slew Rate | 40V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.8V~11V ±1.4V~5.5V |
| Output Current per Channel | 55mA |
| Input Offset Voltage (Vos) | 100μV |
| Gain Bandwidth Product | 50MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 50000 kHz |
| Voltage Gain | 135.56dB |
| Power Supply Rejection Ratio (PSRR) | 75dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Wideband | NO |
LTC6244HVHDD#PBF Overview
It is packaged in an 8-WFDFN Exposed Pad-case that protects the operational amplifiers from damage. Op amps are General Purpose types of amplifier on the chip. Upon delivery, op amp ic is packaged in a Tube case. In recent months, the number of terminations has approached 8. In this case, there are 8 pins on the board. I would like to remind you that this buffer op amp should be powered by an 5V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. 8 pins are available on the instrumentation amplifier. As far as the input offset voltage is concerned, linear amplifier rates at 100μV. For this electrical component, Surface Mount is the recommended mounting type. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. You can run this op amp ic on 7mA . There should be no change in the voltage gain. A instrumentation amplifier like this has 2 circuits. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages.
LTC6244HVHDD#PBF Features
8 Pins
supply voltage of 5V
135.56dB voltage gain
Output Type: Rail-to-Rail
LTC6244HVHDD#PBF Applications
There are a lot of Linear Technology/Analog Devices LTC6244HVHDD#PBF Instrumentational OP Amps applications.
- Active probe
- Proportional counter tubes
- Commercial audio systems
- Large motor controllers
- Signal amplification
- Instrumentation
- Signal operation
- Thermocouples
- Differentiator circuits
- Portable media players
