LTC6247IMS#PBF
| Parameters | |
|---|---|
| Supply Voltage Limit-Max | 5.5V |
| Voltage - Input Offset | 100μV |
| Low-Bias | NO |
| Micropower | NO |
| -3db Bandwidth | 120MHz |
| Bias Current-Max (IIB) @25C | 1μA |
| Programmable Power | NO |
| Wideband | NO |
| Power | NO |
| Voltage Gain-Min | 1300 |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | LTC6247 |
| Pin Count | 10 |
| JESD-30 Code | S-PDSO-G10 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Circuits | 2 |
| Current - Supply | 1.25mA |
| Slew Rate | 90V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 110 dB |
| Current - Input Bias | 400nA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.25V ±1.25V~2.625V |
| Gain Bandwidth Product | 180MHz |
| Unity Gain BW-Nom | 180000 kHz |
| Average Bias Current-Max (IIB) | 1.5μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
LTC6247IMS#PBF Overview
There is a 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) case package that contains the instrumentation amplifiers. An op amp ic of the General Purpose type. In the case of Tube cases, linear amplifier will be delivered. A total of 10 terminations have been reported in the past few weeks. Buffer amplifier has a total of 10 pins on it. Please take in mind that op amp should be run at 5V. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. This electrical part should be mounted using type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. The buffer amp consists of 2 circuits in total. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. There is a recommendation that this electrical part be used with a supply with 1.25mA current rating. A voltage gain of 1300 is the minimum this op amp can achieve.
LTC6247IMS#PBF Features
10 Pins
supply voltage of 5V
Output Type: Rail-to-Rail
LTC6247IMS#PBF Applications
There are a lot of Linear Technology/Analog Devices LTC6247IMS#PBF Instrumentational OP Amps applications.
- Strain gauges
- Biopotential
- Proportional counter tubes
- Video amplifiers
- pH (acidity)
- Medical imaging
- Radar
- Voltage regulation circuit
- Signal amplification
- Automotive sensors
