LTC6248IMS#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-TFSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | LTC6248 |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Power Supplies | 2.7/5V |
| Number of Circuits | 4 |
| Current - Supply | 1.25mA |
| Slew Rate | 90V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 110 dB |
| Current - Input Bias | 400nA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.25V ±1.25V~2.625V |
| Gain Bandwidth Product | 180MHz |
| Unity Gain BW-Nom | 180000 kHz |
| Average Bias Current-Max (IIB) | 1.5μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 5.5V |
| Voltage - Input Offset | 100μV |
| Low-Bias | NO |
| Micropower | NO |
| -3db Bandwidth | 120MHz |
| Bias Current-Max (IIB) @25C | 1μA |
| Programmable Power | NO |
| Wideband | NO |
| Power | NO |
| Voltage Gain-Min | 1300 |
| Height Seated (Max) | 1.1mm |
| RoHS Status | ROHS3 Compliant |
LTC6248IMS#PBF Overview
Packaging for the buffer amplifier is in the form of a 16-TFSOP (0.118, 3.00mm Width) case. A General Purpose-type buffer amplifier is shown here. Instrumentation amplifier is delivered in a Tube case. There is a growing number of terminations approaching the number of 16. Linear amplifier has a total of 16 pins. Please take in mind that op amp should be run at 5V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. This electronic part is best mounted with type Surface Mount. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. On this instrumentation amplifier, there are 4 circuits that are connected together. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. For optimal performance, this electrical part should be connected to a supply with a current of 1.25mA. To conduct electronic part voltage gain higher than 1300.
LTC6248IMS#PBF Features
16 Pins
supply voltage of 5V
Output Type: Rail-to-Rail
LTC6248IMS#PBF Applications
There are a lot of Linear Technology/Analog Devices LTC6248IMS#PBF Instrumentational OP Amps applications.
- Oscilloscopes
- Television
- Test equipment
- Video conversion and routing
- Mobile phone
- Exponential operation circuits
- PDA
- Strain gauges
- pH (acidity)
- Radiation thermometry transducers
