LTC6254CMS#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-TFSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 4 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | LTC6254 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Power Supplies | 2.7/5V |
| Number of Channels | 4 |
| Operating Supply Current | 4.25mA |
| Supply Current-Max | 23.6mA |
| Slew Rate | 280V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 85 dB |
| Current - Input Bias | 1.4μA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.25V ±1.25V~2.625V |
| Output Current per Channel | 100mA |
| Input Offset Voltage (Vos) | 50μV |
| Bandwidth | 720MHz |
| Unity Gain BW-Nom | 630000 kHz |
| Voltage Gain | 95.56dB |
| Average Bias Current-Max (IIB) | 0.7μA |
| Power Supply Rejection Ratio (PSRR) | 68dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 5.5V |
| Voltage - Input Offset | 100μV |
| -3db Bandwidth | 400MHz |
| Bias Current-Max (IIB) @25C | 2.5μA |
| Nominal Gain Bandwidth Product | 720MHz |
| Height Seated (Max) | 1.1mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
LTC6254CMS#PBF Overview
Packaging for the buffer amplifier is in the form of a 16-TFSOP (0.118, 3.00mm Width) case. Buffer amps of this type are called General Purpose-types. A Tube case is used to deliver the buffer op amp. There is a growing number of terminations approaching the number of 16. The pins on this board total to 16 in total. It would be helpful if you could remember that this op amp ic should be powered by an 2.7V battery. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. A total of 16 pins are present on the instrumentation amplifier. Regarding input offset voltage, op amp rates 50μV. Surface Mount is the recommended mounting type of operational amplifiers. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about 0°C~70°C . It is possible to operate this buffer amplifier from a supply current of 4.25mA . There should be no change in the voltage gain at 95.56dB. There are 4 channels on the operational amplifiers. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has.
LTC6254CMS#PBF Features
16 Pins
supply voltage of 2.7V
95.56dB voltage gain
Output Type: Rail-to-Rail
LTC6254CMS#PBF Applications
There are a lot of Linear Technology/Analog Devices LTC6254CMS#PBF Instrumentational OP Amps applications.
- Hand-held batteries
- Switching amplifier
- Integrator circuits
- Weighing systems
- Automotive sensors
- Proportional counter tubes
- Computer workstations
- Radar
- Medical instruments
- Signal operation
