LV8013T-A-MPB-E
| Parameters | |
|---|---|
| Lifecycle Status | OBSOLETE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-TFSOP (0.173, 4.40mm Width) |
| Number of Pins | 24 |
| Operating Temperature | -20°C~75°C TA |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e6 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 24 |
| Terminal Finish | Tin/Bismuth (Sn/Bi) |
| Applications | DC Motors, General Purpose |
| Additional Feature | ALSO OPERATES IN 2 TO 15V SUPPLY |
| HTS Code | 8542.39.00.01 |
| Subcategory | Motion Control Electronics |
| Technology | DMOS |
| Voltage - Supply | 2.7V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 24 |
| Qualification Status | Not Qualified |
| Max Output Current | 3.8A |
| Operating Supply Voltage | 15V |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 512V |
| Supply Voltage-Min (Vsup) | 2.7V |
| Interface | Logic |
| Analog IC - Other Type | BRUSH DC MOTOR CONTROLLER |
| Nominal Supply Current | 1μA |
| Output Configuration | Half Bridge (2) |
| Power Dissipation | 800mW |
| Output Current | 1.2A |
| Output Current per Channel | 1.2A |
| Supply Current-Max (Isup) | 1.2mA |
| Voltage - Load | 2V~15V |
| Fault Protection | Over Temperature |
| Rds On (Typ) | 300m Ω |
| Current - Peak Output | 2A 3.8A |
| Load Type | Inductive |
| Height Seated (Max) | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
LV8013T-A-MPB-E Overview
For packaging, Tube is used.As a cost-saving measure, H bridge is included in the 24-TFSOP (0.173, 4.40mm Width) package.Reliabilbridge drivery can be improved by increasing 2.7V~5.5V's supply voltage.In the way of Surface Mount, H bridge circuit is mounted.As long as -20°C~75°C TA operates at the right temperature, motor driver H bridge will operate normally.A number of applications can be made use of H bridge motor driver, including DC Motors, General Purpose.The board is mounted using Surface Mount.Transmission lines are terminated with H bridges whose characteristic impedance matches their characteristic impedance, known as 24 terminations.Signal interfaces include 24 pins that serve as pronged contacts.A voltage of 5V is used as the supply voltage.The analog IC type is BRUSH DC MOTOR CONTROLLER.A power source can supply a maximum load current of 3.8A when the ambient temperature is specified.Output reaches 2A 3.8A at the maximum current.As a result of the current flowing through the output and power supply pins, there is a current of 1.2A.It is through 24 pins that this bridge driver is able to perform its specific functions.This H bridge motor driver falls under the subcategory of Motion Control Electronics. It is similar to other parts within that category.For the highest level of efficiency, the operating supply voltage is kept at 15V.512V supplies electricity to the electrical load.Also, H-bridge is capable of providing ALSO OPERATES IN 2 TO 15V SUPPLY.
LV8013T-A-MPB-E Features
Available in 24-TFSOP (0.173, 4.40mm Width) Package / Case
Operating Temperature at the range of Surface Mount
Subcategory: 2A 3.8A
Number of Receivers: 15V
With ALSO OPERATES IN 2 TO 15V SUPPLY Drivers
LV8013T-A-MPB-E Applications
There are a lot of ON Semiconductor LV8013T-A-MPB-E Full Bridge Drivers, Half-Bridge Drivers applications.
- High current, low profile DC-DC converters
- High-Performance Gaming Motherboards
- Voltage Regulators
- Desktop Computers
- Dual DC motor
- Voltage Regulators for GPUs
- OA equipments
- Networking Microprocessor Voltage Regulators
- Bipolar stepper motor
- Industrial Fans
