M74HC273RM13TR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 4.5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | M74HC273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Output Current | 5.2mA |
| Number of Bits | 8 |
| Clock Frequency | 66MHz |
| Propagation Delay | 240 ns |
| Turn On Delay Time | 15 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max I(ol) | 0.004 A |
| Max Propagation Delay @ V, Max CL | 25ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| fmax-Min | 24 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
M74HC273RM13TR Overview
The package is in the form of 20-SOIC (0.295, 7.50mm Width). As part of the package Tape & Reel (TR), it is embedded. It is configured with Non-Invertedas an output. The trigger configured with it uses Positive Edge. Surface Mountmounts this electrical part. A supply voltage of 2V~6V is required for operation. A temperature of -55°C~125°C TAis considered to be the operating temperature. This electronic flip flop is of type D-Type. JK flip flop is a part of the 74HCseries of FPGAs. In order for it to function properly, its output frequency should not exceed 66MHz. In total, there are 1 elements. As a result, it consumes 4μA quiescent current. A total of 20 terminations have been made. JK flip flop belongs to M74HC273 family. A voltage of 4.5V provides power to the D latch. A JK flip flop with a 5pFfarad input capacitance is used here. HC/UHis the family of this D flip flop. There is an electronic component mounted in the way of Surface Mount. This board is designed with 20pins on it. The clock edge trigger type for this device is Positive Edge. This device has the base part number FF/Latches. There are 8bits in this flip flop. Vsup reaches 6V, the maximal supply voltage. Normally, the supply voltage (Vsup) should be above 2V. The superior flexibility of this product is achieved by using 8 circuits. Considering the reliability of this T flip flop, it is well suited for TAPE AND REEL. It operates from 2/6V power supplies. With a current output of 5.2mA , it offers maximum design flexibility.
M74HC273RM13TR Features
Tape & Reel (TR) package
74HC series
20 pins
8 Bits
2/6V power supplies
M74HC273RM13TR Applications
There are a lot of STMicroelectronics M74HC273RM13TR Flip Flops applications.
- QML qualified product
- Set-reset capability
- Balanced Propagation Delays
- Communications
- Memory
- Modulo – n – counter
- Individual Asynchronous Resets
- Storage registers
- Computers
- Frequency Dividers
