M74HC273TTR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | NICKEL PALLADIUM GOLD |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 4.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | M74HC273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 66MHz |
| Propagation Delay | 145 ns |
| Turn On Delay Time | 15 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max I(ol) | 0.004 A |
| Max Propagation Delay @ V, Max CL | 25ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| fmax-Min | 24 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
M74HC273TTR Overview
It is embeded in 20-TSSOP (0.173, 4.40mm Width) case. You can find it in the Tape & Reel (TR)package. The output it is configured with uses Non-Inverted. The trigger it is configured with uses Positive Edge. Surface Mountis occupied by this electronic component. A voltage of 2V~6Vis used as the supply voltage. A temperature of -55°C~125°C TAis used in the operation. D-Typeis the type of this D latch. JK flip flop is a part of the 74HCseries of FPGAs. This D flip flop should not have a frequency greater than 66MHz. A total of 1elements are present in it. There is a consumption of 4μAof quiescent energy. A total of 20 terminations have been made. The M74HC273family includes it. The power supply voltage is 4.5V. The input capacitance of this T flip flop is 5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. It is a member of the HC/UHfamily of D flip flop. The electronic part is mounted in the way of Surface Mount. A total of 20pins are provided on this board. A Positive Edgeclock edge trigger is used in this device. The RS flip flops belongs to FF/Latches base part number. There are 8bits in its design. The maximal supply voltage (Vsup) reaches 6V. For normal operation, the supply voltage (Vsup) should be above 2V. Despite its superior flexibility, it relies on 8 circuits to achieve it. As a result of its reliable performance, this T flip flop is suitable for TAPE AND REEL. It runs on 2/6Vvolts of power.
M74HC273TTR Features
Tape & Reel (TR) package
74HC series
20 pins
8 Bits
2/6V power supplies
M74HC273TTR Applications
There are a lot of STMicroelectronics M74HC273TTR Flip Flops applications.
- Bounce elimination switch
- Safety Clamp
- Parallel data storage
- ESD protection
- Balanced 24 mA output drivers
- Patented noise
- Load Control
- Set-reset capability
- Communications
- Data transfer
