M74HC374RM13TR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 4.5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | M74HC374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 90MHz |
| Propagation Delay | 190 ns |
| Turn On Delay Time | 17 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 7.8mA 7.8mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 32ns @ 6V, 150pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
M74HC374RM13TR Overview
The item is packaged in 20-SOIC (0.295, 7.50mm Width)cases. D flip flop is embedded in the Tape & Reel (TR) package. It is configured with Tri-State, Non-Invertedas an output. This trigger uses the value Positive Edge. Surface Mountis in the way of this electric part. A voltage of 2V~6Vis required for its operation. A temperature of -55°C~125°C TAis used in the operation. D-Typedescribes this flip flop. The FPGA belongs to the 74HC series. There should be no greater frequency than 90MHzon its output. D latch consists of 1 elements. It consumes 4μA of quiescent current without being affected by external factors. The number of terminations is 20. If you search by M74HC374, you will find similar parts. The power supply voltage is 4.5V. This JK flip flop has a 5pFfarad input capacitance. Devices in the HC/UHfamily are electronic devices. There is an electronic part that is mounted in the way of Surface Mount. With its 20pins, it is designed to work with most electronic flip flops. This device's clock edge trigger type is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. An electronic part with 8bits has been designed. In this case, the maximum supply voltage (Vsup) reaches 6V. Normally, the supply voltage (Vsup) should be kept above 2V. The superior flexibility of this circuit is achieved by using 8 circuits. Considering its reliability, this T flip flop is well suited for TAPE AND REEL. It operates from 2/6V power supplies. The D flip flop is embedded with 2ports. To operate, the chip has a total of 3 output lines.
M74HC374RM13TR Features
Tape & Reel (TR) package
74HC series
20 pins
8 Bits
2/6V power supplies
M74HC374RM13TR Applications
There are a lot of STMicroelectronics M74HC374RM13TR Flip Flops applications.
- Safety Clamp
- Storage Registers
- Cold spare funcion
- Digital electronics systems
- Divide a clock signal by 2 or 4
- High Performance Logic for test systems
- Asynchronous counter
- Guaranteed simultaneous switching noise level
- Clock pulse
- Computers
