M74HC4052TTR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 100Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 4.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | M74HC405 |
| Pin Count | 16 |
| Polarity | Non-Inverting |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Operating Supply Current | 8μA |
| Power Dissipation | 500mW |
| Propagation Delay | 60 ns |
| Turn On Delay Time | 225 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 2V~6V ±2V~6V |
| Supply Type | Dual |
| Bandwidth | 120MHz |
| Neg Supply Voltage-Nom (Vsup) | -4.5V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 6V |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 1V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 10pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 18ns, 29ns |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Crosstalk | -50dB @ 1kHz |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
M74HC4052TTR Overview
Presented in 16-TSSOP (0.173, 4.40mm Width), this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have the same number of circuits 4:1. Operating temperature extended to -55°C~125°C TA. In total, 16 terminations have occurred. By its 4 channels, the electronic component provides high-quality output. If the voltage supply is 4.5V volts, the electrical component should be turned on and run. This electronic part can be found in the 16 series. SP4T switching circuits are used in these analog switch ics. This multiplexer is composed of 2 circuits. If you are looking for variants of the digital switch, trying search with M74HC405. There is 100Ohm internal resistance in this digital multiplexer. Datasheets for functions of 16 pins are available. It is a typical Multiplexer or Switches analog multiplexer. Users shouldn't supply more than 6V voltage to the switch device. Analog switch ics with Dual supply type are cost-effective. 2V should be the lowest voltage fed to the electronic component. The analogue multiplexer could operate on 8μA current. For this switch, a dual supply voltage is feasible, but it must not exceed 6VWhen using dual power supplies, you should attach at least 1V. Integrated with an analog IC DIFFERENTIAL MULTIPLEXER. Operating 8 inputs is required. The transfer of data can be performed over 120MHz bandwidths.
M74HC4052TTR Features
4 Channels
Switch Circuit: SP4T
8μA Supply Current
-3db Bandwidth: 200MHz
Bandwidth: 120MHz
M74HC4052TTR Applications
There are a lot of STMicroelectronics M74HC4052TTR Analog Switches & Multiplexers ICs applications.
- Battery-powered systems
- Frame Relay Equipment
- Communication systems
- PBX interfaces
- Battery Powered Systems
- Precision test equipment
- Data Acquisition Systems
- Channel Banks
- Cable PC
- Optical Applications
