M74HC4316B1R
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 70Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 4.5V |
| Base Part Number | M74HC43 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Polarity | Non-Inverting |
| Number of Channels | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Power Dissipation | 500mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 115 ns |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±1V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -4.5V |
| Turn-Off Delay Time | 205 ns |
| Max Dual Supply Voltage | 6V |
| -3db Bandwidth | 43MHz |
| On-State Resistance (Max) | 70Ohm |
| Min Dual Supply Voltage | 1V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 1pF 5pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 18ns, 29ns |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Crosstalk | -50dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 21ns |
| Normal Position | NO |
| Height Seated (Max) | 5.1mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Lead Free |
M74HC4316B1R Overview
Presented in 16-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. Advanced packaging method Tube is used to provide high reliability. In Through Hole, this analog switch is mounted. Multiplexers and demultiplexers have the same number of circuits 2:1. Operational temperature extended around -55°C~125°C TA. Total terminations are 16. The electronic part provides high-quality output because it has 4 channels. An 4.5V voltage supply should allow the electrical part to be turned on and run. A key feature of the 16 series is the inclusion of this electronic part as part of its design. A SPDT switching circuit is used for these analog switches. Using the M74HC43 search parameter, you can discover variants of the switch. It has an internal resistance of 70Ohm. Datasheets for functions of 16 pins are available. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users shouldn't supply more than 12V voltage to the switch device. A analog switch ic that has a cost-effective Dual, Single supply type. It is recommended to use 2V as the lowest voltage for the electrical part. A voltage higher than 1μA may cause damage to the switch multiplexer. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 6V. In the case of dual power supplies, you should connect at least 1V. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.
M74HC4316B1R Features
4 Channels
Switch Circuit: SPDT
-3db Bandwidth: 43MHz
M74HC4316B1R Applications
There are a lot of STMicroelectronics M74HC4316B1R Analog Switches & Multiplexers ICs applications.
- Multi-Line E1 Interface Cards
- Cell phones
- Relay replacements
- Fiber In The Loop (FITL)
- Avionics and Military Systems
- Remote wireless modules
- Fault Tolerant Systems
- Precision data acquisition
- Optical Applications
- DSLAMs
