M74HC534B1R
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Series | 74HC |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 4.5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | M74HC53 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Inverted |
| Number of Elements | 1 |
| Polarity | Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 90MHz |
| Propagation Delay | 190 ns |
| Turn On Delay Time | 17 ns |
| Family | HC/UH |
| Logic Function | Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 7.8mA 7.8mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 32ns @ 6V, 150pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 3.93mm |
| Width | 7.62mm |
| RoHS Status | ROHS3 Compliant |
M74HC534B1R Overview
The flip flop is packaged in a case of 20-DIP (0.300, 7.62mm). The package Tubecontains it. Tri-State, Invertedis the output configured for it. The trigger configured with it uses Positive Edge. It is mounted in the way of Through Hole. A voltage of 2V~6Vis used as the supply voltage. In the operating environment, the temperature is -55°C~125°C TA. This logic flip flop is classified as type D-Type. In FPGA terms, D flip flop is a type of 74HCseries FPGA. This D flip flop should not have a frequency greater than 90MHz. A total of 1elements are contained within it. As a result, it consumes 4μA quiescent current and is not affected by external forces. The number of terminations is 20. JK flip flop belongs to M74HC53 family. It is powered from a supply voltage of 4.5V. Its input capacitance is 5pFfarads. Electronic devices of this type belong to the HC/UHfamily. A part of the electronic system is mounted in the way of Through Hole. There are 20pins on it. This device has Positive Edgeas its clock edge trigger type. It is included in FF/Latches. Flip flops designed with 8bits are used in this part. As soon as 6Vis reached, Vsup reaches its maximum value. The supply voltage (Vsup) should be maintained above 2V for normal operation. The D latch runs on a voltage of 2/6V volts. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. This input has 8lines.
M74HC534B1R Features
Tube package
74HC series
20 pins
8 Bits
2/6V power supplies
M74HC534B1R Applications
There are a lot of STMicroelectronics M74HC534B1R Flip Flops applications.
- Convert a momentary switch to a toggle switch
- High Performance Logic for test systems
- Divide a clock signal by 2 or 4
- Consumer
- Matched Rise and Fall
- Memory
- Latch-up performance
- Asynchronous counter
- ESD protection
- Safety Clamp
