M74HC574TTR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74HC |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 4.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | M74HC57 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 90MHz |
| Propagation Delay | 190 ns |
| Turn On Delay Time | 19 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 7.8mA 7.8mA |
| Max I(ol) | 0.006 A |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
M74HC574TTR Overview
The package is in the form of 20-TSSOP (0.173, 4.40mm Width). Package Cut Tape (CT)embeds it. Tri-State, Non-Invertedis the output configured for it. It is configured with a trigger that uses a value of Positive Edge. Surface Mountis positioned in the way of this electronic part. A voltage of 2V~6Vis used as the supply voltage. It is operating at a temperature of -55°C~125°C TA. A flip flop of this type is classified as a D-Type. FPGAs belonging to the 74HCseries contain this type of chip. You should not exceed 90MHzin its output frequency. The list contains 1 elements. There is a consumption of 4μAof quiescent energy. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. The M74HC57 family contains it. The power source is powered by 4.5V. A JK flip flop with a 5pFfarad input capacitance is used here. This D flip flop belongs to the family of HC/UH. It is mounted in the way of Surface Mount. It is designed with 20 pins. A Positive Edgeclock edge trigger is used in this device. This RS flip flops is a part number FF/Latches. The design is based on 8bits. Vsup reaches 6V, the maximal supply voltage. Normally, the supply voltage (Vsup) should be kept above 2V. To achieve this superior flexibility, 8 circuits are used. In light of its reliable performance, this T flip flop is well suited for TAPE AND REEL. There are 2/6V power supplies attached to it. A D flip flop with 2embedded ports is available. There are 3 output Lines, which generate the binary equivalent of the input line whose value is equal to “1” and are available to encode either a decimal or hexadecimal input pattern to typically a binary or “B. C. D” (binary coded decimal) output code.
M74HC574TTR Features
Cut Tape (CT) package
74HC series
20 pins
8 Bits
2/6V power supplies
M74HC574TTR Applications
There are a lot of STMicroelectronics M74HC574TTR Flip Flops applications.
- Power down protection
- 2 – Bit synchronous counter
- Frequency Dividers
- Latch
- Safety Clamp
- Instrumentation
- Divide a clock signal by 2 or 4
- Frequency Divider circuits
- Computers
- Bus hold
