M74HC74RM13TR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 4.535924g |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 4.5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | M74HC74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Voltage | 5V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Output Current | 5.2mA |
| Clock Frequency | 67MHz |
| Propagation Delay | 150 ns |
| Turn On Delay Time | 13 ns |
| Family | HC/UH |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 2μA |
| Number of Inputs | 4 |
| Current - Output High, Low | 5.2mA 5.2mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 26ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.65mm |
| Length | 8.75mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
M74HC74RM13TR Overview
The package is in the form of 14-SOIC (0.154, 3.90mm Width). You can find it in the Tape & Reel (TR)package. There is a Differentialoutput configured with it. This trigger uses the value Positive Edge. There is an electronic component mounted in the way of Surface Mount. A supply voltage of 2V~6V is required for operation. It is operating at -55°C~125°C TA. Logic flip flops of this type are classified as D-Type. The FPGA belongs to the 74HC series. This D flip flop should not have a frequency greater than 67MHz. As a result, it consumes 2μA of quiescent current without being affected by external factors. The number of terminations is 14. This D latch belongs to the family of M74HC74. Power is provided by a 4.5V supply. The input capacitance of this T flip flop is 5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. In terms of electronic devices, this device belongs to the HC/UHfamily of devices. A part of the electronic system is mounted in the way of Surface Mount. Basically, it is designed with a set of 14 pins. A Positive Edgeclock edge trigger is used in this device. There is a FF/Latchesbase part number assigned to the RS flip flops. In order to achieve its superior flexibility, 2 circuits are used. In view of its reliability, this D flip flop is a good fit for TAPE AND REEL. With a current output of 5.2mA , it offers maximum design flexibility. The system employs 4inputs.
M74HC74RM13TR Features
Tape & Reel (TR) package
74HC series
14 pins
M74HC74RM13TR Applications
There are a lot of STMicroelectronics M74HC74RM13TR Flip Flops applications.
- Balanced 24 mA output drivers
- Functionally equivalent to the MC10/100EL29
- Communications
- ATE
- Frequency Divider circuits
- Single Down Count-Control Line
- Control circuits
- Data transfer
- ESCC
- CMOS Process
