M74HCT273RM13TR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | M74HCT273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Voltage | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 80MHz |
| Propagation Delay | 48 ns |
| Turn On Delay Time | 19 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 4mA 4mA |
| Max I(ol) | 0.004 A |
| Max Propagation Delay @ V, Max CL | 30ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
M74HCT273RM13TR Overview
The package is in the form of 20-SOIC (0.295, 7.50mm Width). The package Tape & Reel (TR)contains it. It is configured with Non-Invertedas an output. In the configuration of the trigger, Positive Edgeis used. In this case, the electronic component is mounted in the way of Surface Mount. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. In the operating environment, the temperature is -55°C~125°C TA. It belongs to the type D-Typeof flip flops. In FPGA terms, D flip flop is a type of 74HCTseries FPGA. It should not exceed 80MHzin its output frequency. D latch consists of 1 elements. It consumes 4μA of quiescent current without being affected by external factors. 20terminations have occurred. The M74HCT273 family contains it. A voltage of 5V is used to power it. Its input capacitance is 5pF farads. An electronic device belonging to the family HCTcan be found here. A part of the electronic system is mounted in the way of Surface Mount. The 20pins are designed into the board. This device has Positive Edgeas its clock edge trigger type. There is a base part number FF/Latchesfor the RS flip flops. An electronic part with 8bits has been designed. The superior flexibility of this product is achieved by using 8 circuits. Considering the reliability of this T flip flop, it is well suited for TAPE AND REEL. In order for the device to operate, it requires 5V power supplies. If high efficiency is desired, the supply voltage should be kept at 5V.
M74HCT273RM13TR Features
Tape & Reel (TR) package
74HCT series
20 pins
8 Bits
5V power supplies
M74HCT273RM13TR Applications
There are a lot of STMicroelectronics M74HCT273RM13TR Flip Flops applications.
- Circuit Design
- Shift Registers
- Asynchronous counter
- Consumer
- Bounce elimination switch
- Differential Individual
- Event Detectors
- Cold spare funcion
- ESD protection
- Buffer registers
