M74HCT4051TTR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 120Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 4.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | M74HCT405 |
| Pin Count | 16 |
| Operating Supply Voltage | 5V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Operating Supply Current | 8μA |
| Power Dissipation | 500mW |
| Propagation Delay | 12 ns |
| Turn On Delay Time | 45 ns |
| Logic Function | Demultiplexer, Demux, Multiplexer, Mux |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 4.5V~5.5V ±1V~6V |
| Supply Type | Dual |
| Bandwidth | 190MHz |
| Neg Supply Voltage-Nom (Vsup) | -4.5V |
| Turn-Off Delay Time | 38 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 120Ohm |
| Min Dual Supply Voltage | 1V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 0.75pF 5pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Time (Ton, Toff) (Max) | 34ns, 31ns |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Crosstalk | -50dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 34ns |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
M74HCT4051TTR Overview
The electrical component comes in 16-TSSOP (0.173, 4.40mm Width) packaging, which makes it convenient to ship overseas. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 8:1. Operating temperature around -55°C~125°C TA extended. Total terminations are 16. By its 8 channels, the electronic component provides high-quality output. An 4.5V voltage supply should allow the electrical part to be turned on and run. Electronic part bodies are injected with 16 pins. This multiplexer is composed of 1 circuits. Look for analog switch ic variants by searching with M74HCT405. Analog switches have 120Ohm internal resistance. Please refer to the datasheets for 16 pins functions. This switch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. A cost-effective Dual supply type analogue multiplexer. There should be 4.5V voltage fed to the electrical part below 4.5V. An operating current of 8μA would be sufficient for this switch device. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 6V. It is recommended that you attach at least 1V to your dual power supply. An analog IC with the number SINGLE-ENDED MULTIPLEXER is integrated into this board. There is a voltage range of 5V operating voltages for the electrical part. Operating 8 inputs is required. In 190MHz-bandwidths, data can be transferred.
M74HCT4051TTR Features
8 Channels
8μA Supply Current
Bandwidth: 190MHz
M74HCT4051TTR Applications
There are a lot of STMicroelectronics M74HCT4051TTR Analog Switches & Multiplexers ICs applications.
- SDH
- Medical systems
- Audio signal routing
- Signal routing between systems
- High reliability control systems
- ISDN NT1/TA
- Sample hold systems
- Avionics and Military Systems
- High-Voltage
- Digital Cross-Connects
