M74HCT74TTR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | M74HCT74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Clock Frequency | 48MHz |
| Propagation Delay | 33 ns |
| Turn On Delay Time | 21 ns |
| Family | HCT |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 2μA |
| Current - Output High, Low | 4mA 4mA |
| Max I(ol) | 0.004 A |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 33ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
M74HCT74TTR Overview
In the form of 14-TSSOP (0.173, 4.40mm Width), it has been packaged. There is an embedded version in the package Tape & Reel (TR). In the configuration, Differentialis used as the output. This trigger is configured to use Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. The supply voltage is set to 4.5V~5.5V. It is operating at -55°C~125°C TA. This logic flip flop is classified as type D-Type. In this case, it is a type of FPGA belonging to the 74HCT series. It should not exceed 48MHzin terms of its output frequency. There is a consumption of 2μAof quiescent energy. There are 14 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. JK flip flop belongs to M74HCT74 family. The power supply voltage is 5V. Its input capacitance is 5pF farads. An electronic device belonging to the family HCTcan be found here. Electronic part Surface Mountis mounted in the way. A total of 14pins are provided on this board. This device has the clock edge trigger type of Positive Edge. It is part of the FF/Latchesbase part number family. Due to its superior flexibility, it uses 2 circuits. Compared to other similar T flip flops, this device offers reliable performance and is well suited for TAPE AND REEL. The D latch operates on 5V volts. The supply voltage should be maintained at 5V for high efficiency. There are 1 output lines on it.
M74HCT74TTR Features
Tape & Reel (TR) package
74HCT series
14 pins
5V power supplies
M74HCT74TTR Applications
There are a lot of STMicroelectronics M74HCT74TTR Flip Flops applications.
- Parallel data storage
- Dynamic threshold performance
- Computing
- Synchronous counter
- Computers
- Latch
- Divide a clock signal by 2 or 4
- Frequency Divider circuits
- Convert a momentary switch to a toggle switch
- Frequency division
