MAX13081EESA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Manufacturer Package Identifier | S8+4 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | MATTE TIN |
| HTS Code | 8542.39.00.01 |
| Subcategory | Line Driver or Receivers |
| Technology | BICMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX13081E |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Qualification Status | Not Qualified |
| Power Supplies | 5V |
| Supply Current-Max | 1.8mA |
| Data Rate | 250kbps |
| Differential Output | YES |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Full |
| Receiver Hysteresis | 100mV |
| Interface Standard | EIA-422; EIA-485 |
| Receive Delay-Max | 200 ns |
| Transmit Delay-Max | 1800 ns |
| Output Low Current-Max | 0.001A |
| Out Swing-Min | 2 V |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX13081EESA+T Overview
LED drivers benefit from this IC's enhanced 8-SOIC (0.154, 3.90mm Width) package.The Tape & Reel (TR) package contains this receiver.Being a Transceiver can transceiver, this part has empowered many solutions to serve for a variety of applications.Ideally, you should place this wide receiver on a Surface Mount-type PCB or development board.A differential driver like this uses 4.5V~5.5V of power.During operation, this electronic part may have up to 1/1 eligible receivers/drivers.IC receiver has been designed primarily for applications operating at -40°C~85°C.An output voltage range of 5V is sufficient to run this line driver ic efficiently.In order to drive and receive signals from data, this wide receiver has 8 terminations integrated.This transceiver is packaged with 8 market standard pinoutsAs the base part number MAX13081E identifies the product type, temperature, package, etc., you can try searching with it to get more variants of this part.There is a capability of 1-bit resolution with this ic receiver.There is usually a 1-bit resolution specified for this receiver when it is used.In this category, this rf transceiver module belongs to the Line Driver or Receivers subcategory.There is one driver IC that is designed to operate from a 5V power supply, and only one driver IC in total.There should be enough current supplied to the VCC pin of the part, but not more than 1.8mA.
MAX13081EESA+T Features
Tape & Reel (TR) package
8 pin count
5V power supply
MAX13081EESA+T Applications
There are a lot of Maxim Integrated MAX13081EESA+T Drivers/Receivers/Transceivers applications.
- Servers
- Pocket PC
- Thermal management
- AV receiver
- transmission relay
- Wireless transmission
- Clock radio
- Wireless access points
- interconnection between computers
- IPTV front end
