MAX13088ECSA+
| Parameters | |
|---|---|
| Terminal Finish | Matte Tin (Sn) |
| HTS Code | 8542.39.00.01 |
| Subcategory | Line Driver or Receivers |
| Technology | BICMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX13088E |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Qualification Status | Not Qualified |
| Power Supplies | 5V |
| Supply Current-Max | 1.8mA |
| Data Rate | 16Mbps |
| Differential Output | YES |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Half |
| Receiver Hysteresis | 100mV |
| Interface Standard | EIA-422; EIA-485 |
| Receive Delay-Max | 80 ns |
| Transmit Delay-Max | 50 ns |
| Output Low Current-Max | 0.001A |
| Out Swing-Min | 2 V |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Manufacturer Package Identifier | S8+4 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Transceiver |
MAX13088ECSA+ Overview
This LED driver IC features an enhanced 8-SOIC (0.154, 3.90mm Width) package for driving common LEDs.There is a Tube package for this receiver.Since this is a Transceiver can transceiver, many solutions can use it for a variety of functions.PCB or development board with Surface Mount-type connectors can accommodate this wide receiver.Power supply for this differential driver is 4.5V~5.5V.As many as 1/1 eligible receivers/drivers can be used simultaneously with this electronic part.As its name implies, this ic receiver is designed for applications where 0°C~70°C is the operating temperature.Wide receiver can operate within the range of 5V supply voltages efficiently.In order to drive and receive signals from data, this wide receiver has 8 terminations integrated.ICs that are packaged with market standard pinouts are available on the market.Since the base part number MAX13088E describes the product type, temperature, package, etc., you might get more options by searching with it.In this ic receiver, the resolution was able to be set to a maximum of 1 bits.There is typically a resolution of 1 bits specified with this receiver.There is a subcategory named Line Driver or Receivers for this rf transceiver module.It is designed so that it can be operated from a 5V power supply with this driver IC.To power the ic receiver, sufficient current but not more than 1.8mA should be supplied to its VCC pin.
MAX13088ECSA+ Features
Tube package
8 pin count
5V power supply
MAX13088ECSA+ Applications
There are a lot of Maxim Integrated MAX13088ECSA+ Drivers/Receivers/Transceivers applications.
- Gigabit Ethernet
- Switching system
- SONET/SDH Network
- Cable network front end
- Mainframes, workstations or storage devices
- Televisions
- Desktop PC
- Radio transmission
- transmission relay
- Wireless modems
