MAX13433EESD+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 259.19969mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2010 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Line Driver or Receivers |
| Technology | BICMOS |
| Voltage - Supply | 3V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX13433 |
| Pin Count | 14 |
| Operating Supply Voltage | 5V |
| Interface | RS-485 |
| Operating Supply Current | 2mA |
| Propagation Delay | 50 ns |
| Data Rate | 16Mbps |
| Differential Output | YES |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Full |
| Receiver Hysteresis | 15mV |
| Number of Transceivers | 1 |
| Receive Delay-Max | 80 ns |
| Simplex/Duplex | Full Duplex |
| Height | 1.5mm |
| Length | 8.75mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
MAX13433EESD+ Overview
This driver chip is excellent for driving common LEDs due to its enhanced 14-SOIC (0.154, 3.90mm Width) package.This receiver is mounted in the Tube package.With its Transceiver can transceiver design, this part can be incorporated into a wide range of solutions.Any Surface Mount-type PCB or development board can be used with this wide receiver.It takes 3V~5.5V from the power supply to run this differential driver.At any given time, there can be up to 1/1 eligible receivers/drivers for this electronic part.IC receiver has been designed primarily for applications operating at -40°C~85°C.This line driver ic can operate efficiently with a supply voltage range of 1.8V.The integrated terminations of this wide receiver allow it to drive and receive signals from data.In this package, you will find 14 market-standard pinouts for this transceiver.The base part number MAX13433 identifies the product type, temperature, package, etc., so you can search for more variants by using it.An enhanced power dissipation driver IC with 14 pins.The package size of this optical transceiver has been dramatically reduced by downsizing ICs and using high-density Surface Mount mounting techniques.It is important to note that this ic receiver had a maximum resolution of 1 bits.There is usually a 1-bit resolution specified for this receiver when it is used.This transceiver module is designed to operate from an input voltage supply of 5V.There is a subcategory named Line Driver or Receivers for this rf transceiver module.There are 1 transceivers implemented in this module isolated transceiver.Using the input voltage of 2mA, this integrating circuit is capable of driving LEDs with an output voltage of 12 volts.
MAX13433EESD+ Features
Tube package
14 pin count
14 pins
MAX13433EESD+ Applications
There are a lot of Maxim Integrated MAX13433EESD+ Drivers/Receivers/Transceivers applications.
- Wireless transmission
- Switching system
- Precision engineering measurement
- Wireless smart house
- Routers
- Televisions
- interconnection between computers
- Wireless HD Photography
- Wireless access points
- High-speed computer links
