MAX13444EASA+
| Parameters | |
|---|---|
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Subcategory | Line Driver or Receivers |
| Technology | BICMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX13444 |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Operating Supply Current | 30mA |
| Propagation Delay | 50 ns |
| Data Rate | 250kbps |
| Differential Output | YES |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Half |
| Receiver Hysteresis | 25mV |
| Number of Transceivers | 1 |
| ESD Protection | Yes |
| Receive Delay-Max | 2000 ns |
| Transmit Delay-Max | 2000 ns |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 506.605978mg |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
MAX13444EASA+ Overview
Due to the enhanced 8-SOIC (0.154, 3.90mm Width) package, this driver IC is excellent for driving common LEDs.There is a Tube package for this receiver.The Transceiver can transceiver technology has enabled this part to power many solutions for a variety of uses.Ideally, you should place this wide receiver on a Surface Mount-type PCB or development board.This differential driver uses 4.75V~5.25V for power supply.There can be up to 1/1 eligible receivers/drivers on the field at the same time with this electronic part.The operating temperature of this ic receiver is -40°C~125°C. It is primarily designed for applications with low temperatures.This line driver ic can operate efficiently with a supply voltage range of 5V.8 terminations are integrated into this wide receiver for driving and receiving signals from data.This transceiver is packaged with 8 market standard pinoutsWith the part number MAX13444 identifying the product type, temperature, package, etc., you can search with it to see more variants.The driver IC has improved power dissipation control.Package size is drastically reduced by downsizing ICs and mounting them in high-density Surface Mount arrays.As a result of the ic receiver, the resolution of the driver was increased to 1 bits.In most cases, the receiver will be specified with a 1-bit resolution.There is a 5V input voltage supply that can be used to operate this transceiver module.In this category, this rf transceiver module belongs to the Line Driver or Receivers subcategory.This driver IC is designed to operate from a 5V power supply.Transceivers implemented by this IC total 1 in total.There is no matter what the input voltage is. The integrating circuit is able to drive LEDs with an input voltage of 30mA.
MAX13444EASA+ Features
Tube package
8 pin count
8 pins
5V power supply
MAX13444EASA+ Applications
There are a lot of Maxim Integrated MAX13444EASA+ Drivers/Receivers/Transceivers applications.
- Cable network front end
- Wireless showroom
- Satellite communications networks
- Metro access rings
- Telecom applications
- Wireless access points
- Precision engineering measurement
- interconnection between computers
- Mainframes, workstations or storage devices
- Datacom networking applications
