MAX14662ETI+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 28-WFQFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 28 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2014 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| Resistance | 1Ohm |
| Max Power Dissipation | 2.285W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.4mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX14662 |
| Operating Supply Voltage | 3.3V |
| Number of Channels | 1 |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.6V |
| Max Supply Current | 525μA |
| Turn On Delay Time | 5.5 μs |
| Supply Type | Single |
| Turn-Off Delay Time | 35 μs |
| -3db Bandwidth | 400MHz |
| On-State Resistance (Max) | 1Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 40 dB |
| Current - Leakage (IS(off)) (Max) | 50nA |
| On-state Resistance Match-Nom | 0.02Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 35μs (Max), 5.5μs (Typ) |
| Channel-to-Channel Matching (ΔRon) | 20m Ω |
| Crosstalk | -80dB @ 1MHz |
| Switch-on Time-Max | 60000ns |
| Voltage - Supply, Single (V+) | 1.6V~5.5V |
| Length | 4mm |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
MAX14662ETI+ Overview
Due to its 28-WFQFN Exposed Pad packaging, the electronic part is convenient for international shipping. This high-reliability packaging method uses advanced packaging methods Tube. In Surface Mount, this analog switch is mounted. 1:1 is the ratio of multiplexer to demultiplexer circuits. Extended operating temperature around -40°C~85°C TA. 28 terminations have been made so far. Due to its 1 channels, the electrical component produces high-quality output. Powered by a 3.3V voltage supply, the electrical part should be switched on and run. On the other hand, analog switches can be constructed using SPST - NO switching circuits. A 8 circuit is present in this switch device. Search with MAX14662 if you are looking for analog multiplexer variants. Analog switches have 1Ohm internal resistance. The functions of 28 pins can be found in the datasheets. A voltage higher than 5.5V should not normally be supplied to the switches. The analog switch ic is of the Single supply type and is cost-effective. The lowest voltage fed to the electronic component should be 1.6V. The voltage required by this switch device is 1.6V~5.5V, draining from a single voltage supply. A voltage higher than 525μA may cause damage to the switch multiplexer. 3.3V operating voltages can be used with this electrical part.
MAX14662ETI+ Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 400MHz
MAX14662ETI+ Applications
There are a lot of Maxim Integrated MAX14662ETI+ Analog Switches & Multiplexers ICs applications.
- PCMCIA cards
- SDH
- Digital Cross-Connects
- DSUs
- ATM
- Cross Connects
- Fiber In The Loop (FITL)
- Frame Relay Equipment
- Industrial control systems
- Switching Systems
