MAX14662ETI+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 28-WFQFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 28 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2014 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| Resistance | 1Ohm |
| Max Power Dissipation | 2.285W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.4mm |
| Base Part Number | MAX14662 |
| Operating Supply Voltage | 3.3V |
| Number of Channels | 1 |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.6V |
| Max Supply Current | 525μA |
| Turn On Delay Time | 5.5 μs |
| Supply Type | Single |
| Turn-Off Delay Time | 35 μs |
| -3db Bandwidth | 400MHz |
| On-State Resistance (Max) | 1Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 40 dB |
| Current - Leakage (IS(off)) (Max) | 50nA |
| On-state Resistance Match-Nom | 0.02Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 35μs (Max), 5.5μs (Typ) |
| Channel-to-Channel Matching (ΔRon) | 20m Ω |
| Crosstalk | -80dB @ 1MHz |
| Switch-on Time-Max | 60000ns |
| Voltage - Supply, Single (V+) | 1.6V~5.5V |
| Length | 4mm |
| RoHS Status | ROHS3 Compliant |
MAX14662ETI+T Overview
The electronic component is convenient to ship overseas because it is packed in a 28-WFQFN Exposed Pad. This packaging method provides high reliability because it uses advanced packaging techniques. A switch device like this is mounted in Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operational temperature extended around -40°C~85°C TA. Totally, there are 28 terminations. As a result of its 1 channels, this electronic component provides high-quality output. An 3.3V voltage supply should allow the electrical part to be turned on and run. Multiplexers built on a SPST - NO switching circuit are built. A 8 circuit is present in this switch device. Look for analog switch ic variants by searching with MAX14662. It has an internal resistance of 1Ohm. Datasheets for functions of 28 pins are available. Users should never supply a voltage higher than 5.5V to a switch device. The digital multiplexer has a low cost Single supply. The lowest voltage the electronic part should receive is 1.6V. Using only a single voltage supply, this analog switch requires 1.6V~5.5V voltage. It may damage the digital multiplexer if the voltage is higher than 525μA. The electronic component can function from 3.3V.
MAX14662ETI+T Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 400MHz
MAX14662ETI+T Applications
There are a lot of Maxim Integrated MAX14662ETI+T Analog Switches & Multiplexers ICs applications.
- Relay replacements
- Remote Powered Equipment
- Precision test equipment
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- E1 Network Equipment
- Private Branch Exchange (PBX)
- SDH
- New designs requiring multiplexer functions
- Medical systems
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
