banner_page

MAX14689EWL+T

200μs, 30μs DPDT 450mOhm BOTTOM Analog Switches BREAK-BEFORE-MAKE MAX14689 100nA 9-WFBGA, WLBGA


  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-MAX14689EWL+T
  • Package: 9-WFBGA, WLBGA
  • Datasheet: PDF
  • Stock: 752
  • Description: 200μs, 30μs DPDT 450mOhm BOTTOM Analog Switches BREAK-BEFORE-MAKE MAX14689 100nA 9-WFBGA, WLBGA(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Contact Plating Copper, Silver, Tin
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 9-WFBGA, WLBGA
Number of Pins 9
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2013
Series Beyond-the-Rails™
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 9
Resistance 450mOhm
Subcategory Multiplexer or Switches
Max Power Dissipation 963.8mW
Technology BICMOS
Terminal Position BOTTOM
Terminal Form BALL
Peak Reflow Temperature (Cel) NOT SPECIFIED
Number of Functions 1
Terminal Pitch 0.4mm
Time@Peak Reflow Temperature-Max (s) NOT SPECIFIED
Base Part Number MAX14689
Output SEPARATE OUTPUT
Qualification Status Not Qualified
Operating Supply Voltage 2.5V
Polarity Non-Inverting
Number of Circuits 1
Max Supply Voltage 5.5V
Min Supply Voltage 1.6V
Max Supply Current 125μA
Turn On Delay Time 200 μs
Supply Type Single
Turn-Off Delay Time 30 μs
-3db Bandwidth 110MHz
On-State Resistance (Max) 450mOhm
Multiplexer/Demultiplexer Circuit 2:2
Current - Leakage (IS(off)) (Max) 100nA
Channel Capacitance (CS(off), CD(off)) 25pF
Switch Circuit DPDT
Switch Time (Ton, Toff) (Max) 200μs, 30μs
Channel-to-Channel Matching (ΔRon) 5m Ω
Crosstalk -100dB @ 100kHz
Switching BREAK-BEFORE-MAKE
Switch-on Time-Max 250000ns
Voltage - Supply, Single (V+) 1.6V~5.5V
RoHS Status ROHS3 Compliant

MAX14689EWL+T Overview


Packed in 9-WFBGA, WLBGA, the electronic component is convenient for shipping overseas. High reliability is achieved by using advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. 2:2 is the ratio of multiplexer to demultiplexer circuits. Extended operating temperature around -40°C~85°C TA. Totally, there are 9 terminations. Based on DPDT switching circuits, these analog multiplexers work. 1 circuits are used in this analogue multiplexer. Try searching with MAX14689 if you're looking for variants. In this multiplexer, the internal resistance is 450mOhm. For details about the functions of 9 pins, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 5.5V. A cost-effective Single supply type analogue multiplexer. 1.6V should be the lowest voltage fed to the electronic component. Draining from a single voltage supply, this analog switch requires a voltage of 1.6V~5.5V. A digital multiplexer may suffer damage if voltage is applied above 125μA. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. A voltage of 2.5V can be used to operate the electronic component. The Beyond-the-Rails? series is responsible for it.

MAX14689EWL+T Features


Switch Circuit: DPDT
-3db Bandwidth: 110MHz

MAX14689EWL+T Applications


There are a lot of Maxim Integrated MAX14689EWL+T Analog Switches & Multiplexers ICs applications.

  • Signal routing between systems
  • Microprocessor controlled systems
  • Mechanical reed relay replacement
  • Public switching systems
  • Audio signal routing
  • USB 1.1 signal switching circuits
  • Transmit
  • ISDN NT1/TA
  • DSUs
  • Private Branch Exchange (PBX)

Write a review

Note: HTML is not translated!
    Bad           Good