Parameters |
Factory Lead Time |
1 Week |
Contact Plating |
Tin |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
16 |
Weight |
172.98879mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2008 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Termination |
SMD/SMT |
ECCN Code |
EAR99 |
Resistance |
130Ohm |
Max Power Dissipation |
890mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
35V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX14752 |
Pin Count |
16 |
Output Type |
Fixed |
Operating Supply Voltage |
36V |
Number of Channels |
8 |
Number of Circuits |
1 |
Max Supply Voltage |
72V |
Min Supply Voltage |
20V |
Nominal Supply Current |
270mA |
Max Supply Current |
600μA |
Propagation Delay |
10 μs |
Turn On Delay Time |
25 μs |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
20V~72V ±10V~36V |
Supply Type |
Dual, Single |
Bandwidth |
20MHz |
Neg Supply Voltage-Nom (Vsup) |
-35V |
Turn-Off Delay Time |
2 μs |
Max Dual Supply Voltage |
36V |
On-State Resistance (Max) |
130Ohm |
Min Dual Supply Voltage |
10V |
High Level Output Current |
100mA |
Multiplexer/Demultiplexer Circuit |
8:1 |
Off-state Isolation-Nom |
65 dB |
Current - Leakage (IS(off)) (Max) |
20nA |
Channel Capacitance (CS(off), CD(off)) |
3.7pF |
On-state Resistance Match-Nom |
0.5Ohm |
Switch Time (Ton, Toff) (Max) |
25μs, 2μs |
Charge Injection |
200pC |
Channel-to-Channel Matching (ΔRon) |
500m Ω |
Crosstalk |
-62dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
25000ns |
Switch-off Time-Max |
2000ns |
Height |
900μm |
Length |
5mm |
Width |
4.4mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
MAX14752EUE+ Overview
Due to its 16-TSSOP (0.173, 4.40mm Width) packaging, the electronic part is convenient for international shipping. To ensure high reliability, a new packaging method Tube is used. There is an analog multiplexer mounted in position Surface Mount. 8:1 is the ratio between multiplexers and demultiplexers. The operating temperature is extended to around -40°C~85°C TA. The total number of terminations is 16. As a result of its 8 channels, this electronic component provides high-quality output. An 35V voltage supply should allow the electrical part to be turned on and run. An injection of 16 pins is performed into the body of the electrical component. 1 circuits are used in this analogue multiplexer. Using the MAX14752 search parameter, you can discover variants of the switch. In this multiplexer, the internal resistance is 130Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. A voltage higher than 72V should not normally be supplied to the switches. Analogue multiplexers of the Dual, Single supply type that are cost-effective. 20V should be the lowest voltage fed to the electronic component. A digital multiplexer may suffer damage if voltage is applied above 600μA. For this switch, a dual supply voltage is feasible, but it must not exceed 36VA dual power supply should have at least 10V voltage attached. A voltage of 36V can be used to operate the electronic component. The transfer of data can be performed over 20MHz bandwidths.
MAX14752EUE+ Features
8 Channels
Bandwidth: 20MHz
MAX14752EUE+ Applications
There are a lot of Maxim Integrated MAX14752EUE+ Analog Switches & Multiplexers ICs applications.
- ISDN NT1/TA
- Fiber In The Loop (FITL)
- Battery Powered Instruments
- Medical
- SDH
- Modems
- T1/E1 Terminals
- MP3 players
- Transmit
- High reliability control systems