MAX14757EUE+

60μs, 3μs SPST - NO 10Ohm Analog Switches BREAK-BEFORE-MAKE MAX14757 16 Pins 2.5nA 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX14757EUE+
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 347
Description: 60μs, 3μs SPST - NO 10Ohm Analog Switches BREAK-BEFORE-MAKE MAX14757 16 Pins 2.5nA 16-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Number of Pins	16
Weight	172.98879mg
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2011
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	10Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	889mW
Technology	BICMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	MAX14757
Output	SEPARATE OUTPUT
Pin Count	16
Number of Channels	1
Number of Circuits	4
Max Supply Voltage	70V
Min Supply Voltage	10V
Operating Supply Current	500μA
Max Supply Current	800μA
Throw Configuration	SPST
Turn On Delay Time	60 μs
Voltage - Supply, Single/Dual (±)	10V~70V ±10V~35V
Supply Type	Dual, Single
Turn-Off Delay Time	3 μs
Max Dual Supply Voltage	35V
-3db Bandwidth	145MHz
On-State Resistance (Max)	10Ohm
Min Dual Supply Voltage	10V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	65 dB
Current - Leakage (IS(off)) (Max)	2.5nA
Channel Capacitance (CS(off), CD(off))	35pF
On-state Resistance Match-Nom	0.3Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	60μs, 3μs
Charge Injection	580pC
Channel-to-Channel Matching (ΔRon)	300m Ω
Crosstalk	-96dB @ 10MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	60000ns
Switch-off Time-Max	3000ns
Normal Position	NO
Height	950μm
Length	5.1mm
Width	4.5mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant

MAX14757EUE+ Overview

This electronic part is conveniently packaged in 16-TSSOP (0.173, 4.40mm Width), making it easy to ship abroad. To ensure high reliability, a new packaging method Tube is used. Surface Mount is where this multiplexer is located. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -40°C~85°C TA extended. Total terminations are 16. A electrical component with 1 channels is capable of high-quality output. An electrical component like this is included in the 16 series. These analog multiplexers are built based on SPST - NO switching circuits. The circuits in this analogue multiplexer number 4. Try searching for the analog switch ic with MAX14757 if you are looking for variants. There is 10Ohm internal resistance in this digital multiplexer. To find out what the 16 pins do, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. It is normally recommended that users do not supply the multiplexer with voltages higher than 70V. The analog switch ic is of the Dual, Single supply type and is cost-effective. 10V is the lowest voltage that should be fed to the electronic electronic part. The analogue multiplexer could operate on 500μA current. If you put voltage higher than 800μA on the digital multiplexer, damage may occur. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 35V. With dual power supplies, you should attach at least 10V. The outputs of this digital multiplexer are SEPARATE OUTPUT in number.