Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
16 |
Weight |
172.98879mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2011 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
10Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
889mW |
Technology |
BICMOS |
Terminal Form |
GULL WING |
Number of Functions |
4 |
Terminal Pitch |
0.65mm |
Base Part Number |
MAX14758 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Number of Channels |
2 |
Number of Circuits |
4 |
Max Supply Voltage |
70V |
Min Supply Voltage |
10V |
Operating Supply Current |
500μA |
Max Supply Current |
800μA |
Throw Configuration |
SPST |
Turn On Delay Time |
60 μs |
Voltage - Supply, Single/Dual (±) |
10V~70V ±10V~35V |
Supply Type |
Dual, Single |
Turn-Off Delay Time |
3 μs |
Max Dual Supply Voltage |
35V |
-3db Bandwidth |
145MHz |
On-State Resistance (Max) |
10Ohm |
Min Dual Supply Voltage |
10V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
65 dB |
Current - Leakage (IS(off)) (Max) |
2.5nA |
Channel Capacitance (CS(off), CD(off)) |
35pF |
On-state Resistance Match-Nom |
0.3Ohm |
Switch Circuit |
SPST - NO/NC |
Switch Time (Ton, Toff) (Max) |
60μs, 3μs |
Charge Injection |
580pC |
Channel-to-Channel Matching (ΔRon) |
300m Ω |
Crosstalk |
-96dB @ 10MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
60000ns |
Switch-off Time-Max |
3000ns |
Height Seated (Max) |
1.1mm |
Length |
5mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
MAX14758EUE+ Overview
Due to its 16-TSSOP (0.173, 4.40mm Width) packaging, the electronic part is convenient for international shipping. High reliability is ensured by the advanced packaging method Tube. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have a ratio of 1:1. Increasing operating temperature to around -40°C~85°C TA. Totally, there are 16 terminations. The electronic part delivers high-quality output through its 2 channels. 16 pins are injected to the electronic part body. Based on SPST - NO/NC switching circuits, these analog multiplexers work. A 4 circuit is present in this switch device. Try searching for the analog switch ic with MAX14758 if you are looking for variants. A 10Ohm internal resistance characterizes this multiplexer. For functions related to 16 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. Users should never supply a voltage higher than 70V to a switch device. The analog switch ic is of the Dual, Single supply type and is cost-effective. 10V is the lowest voltage the electrical component should receive. For this digital switch to work, 500μA current would suffice. A digital multiplexer may suffer damage if voltage is applied above 800μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 35V. With dual power supplies, you should attach at least 10V. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.
MAX14758EUE+ Features
2 Channels
Switch Circuit: SPST - NO/NC
500μA Supply Current
-3db Bandwidth: 145MHz
MAX14758EUE+ Applications
There are a lot of Maxim Integrated MAX14758EUE+ Analog Switches & Multiplexers ICs applications.
- Communication systems
- Mechanical reed relay replacement
- SONET
- T1/E1 Terminals
- Microwave transmission systems
- Central office
- Signal routing between systems
- Digital cross connects (DSX-1)
- High-Voltage
- DSLAMs