MAX14759ETA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-WDFN Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 1Ohm |
| Max Power Dissipation | 1.9512W |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX14759 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 4.1mA |
| Nominal Supply Current | 6mA |
| Max Supply Current | 6mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 152 μs |
| Supply Type | Single |
| Bandwidth | 100MHz |
| Turn-Off Delay Time | 1.12 ms |
| On-State Resistance (Max) | 1Ohm |
| High Level Output Current | 500mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 77 dB |
| Current - Leakage (IS(off)) (Max) | 250nA |
| On-state Resistance Match-Nom | 0.0024Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 300μs, 1ns |
| Charge Injection | 1370pC |
| Channel-to-Channel Matching (ΔRon) | 2.4m Ω |
| Crosstalk | -83dB @ 100kHz |
| Switch-on Time-Max | 300000ns |
| Voltage - Supply, Single (V+) | 3V~5.5V |
| Length | 3mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
MAX14759ETA+T Overview
The electrical component comes in 8-WDFN Exposed Pad packaging, which makes it convenient to ship overseas. High reliability is achieved by using advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. Total terminations are 8. By its 1 channels, the electronic component provides high-quality output. When a voltage supply of 5V is used, the electronic component should be turned on and run. Circuits based on SPST - NO switching are used to construct these analog switch ics. There are 1 circuits in this multiplexer. Try searching for MAX14759 variants of the analog switch ic. As far as internal resistance is concerned, it has 1Ohm. Please refer to the datasheets for 8 pins functions. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. Digital switch that provides Single power at a cost-effective price. The lowest voltage fed to the electronic component should be 3V. This multiplexer would work with 4.1mA current. This analogue multiplexer requires a voltage of 3V~5.5V when it drains from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 6mA. This switch operates within the bandwidth of 100MHz.
MAX14759ETA+T Features
1 Channels
Switch Circuit: SPST - NO
4.1mA Supply Current
Bandwidth: 100MHz
MAX14759ETA+T Applications
There are a lot of Maxim Integrated MAX14759ETA+T Analog Switches & Multiplexers ICs applications.
- Digital cross connects (DSX-1)
- Automotive applications
- Medical systems
- Avionics
- Audio/video switches
- Video signal routing
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Battery-powered systems
- Industrial
- Industrial control systems
