MAX14761ETB+T

300μs, 1ns SPST - NO/NC 2Ohm DUAL Analog Switches MAX14761 250nA 5V 10-WFDFN Exposed Pad

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX14761ETB+T
Package: 10-WFDFN Exposed Pad
Datasheet: PDF
Stock: 962
Description: 300μs, 1ns SPST - NO/NC 2Ohm DUAL Analog Switches MAX14761 250nA 5V 10-WFDFN Exposed Pad(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Contact Plating	Tin
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	10-WFDFN Exposed Pad
Number of Pins	10
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2012
JESD-609 Code	e3
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	10
Resistance	2Ohm
Max Power Dissipation	1.9512W
Technology	BICMOS
Terminal Position	DUAL
Number of Functions	2
Supply Voltage	5V
Terminal Pitch	0.5mm
Base Part Number	MAX14761
Operating Supply Voltage	5V
Polarity	Non-Inverting
Number of Channels	1
Number of Circuits	2
Max Supply Voltage	5.5V
Min Supply Voltage	3V
Operating Supply Current	4.1mA
Throw Configuration	SPST
Supply Type	Single
-3db Bandwidth	100MHz
On-State Resistance (Max)	2Ohm
High Level Output Current	250mA
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	77 dB
Current - Leakage (IS(off)) (Max)	250nA
On-state Resistance Match-Nom	0.0051Ohm
Switch Circuit	SPST - NO/NC
Switch Time (Ton, Toff) (Max)	300μs, 1ns
Charge Injection	1370pC
Channel-to-Channel Matching (ΔRon)	5.1m Ω
Crosstalk	-83dB @ 100kHz
Switch-on Time-Max	300000ns
Voltage - Supply, Single (V+)	3V~5.5V
Height Seated (Max)	0.8mm
Length	3mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant

MAX14761ETB+T Overview

As the electronic part is packed in 10-WFDFN Exposed Pad, international shipping is convenient. High reliability is achieved by using advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Increasing operating temperature to around -40°C~85°C TA. In total, there are 10 terminations. A 1 channel electronic part produces high-quality output. When a voltage supply of 5V is used, the electronic component should be turned on and run. These analog multiplexers are built based on SPST - NO/NC switching circuits. 2 circuits are used in this analogue multiplexer. Search with MAX14761 if you are looking for analog multiplexer variants. The internal resistance of this digital multiplexer is 2Ohm. The functions of 10 pins can be found in the datasheets. Users shouldn't supply more than 5.5V voltage to the switch device. The digital multiplexer has a low cost Single supply. 3V should be the lowest voltage fed to the electronic component. For this digital switch to work, 4.1mA current would suffice. A voltage of 3V~5.5V is required for this switch device, which drains from a single voltage source. Operating voltages range from 5V.