banner_page

MAX14763ETA+T

1.8μs, 1ns SPDT 2Ohm DUAL Analog Switches MAX14763 250nA 5V 8-WDFN Exposed Pad


  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-MAX14763ETA+T
  • Package: 8-WDFN Exposed Pad
  • Datasheet: PDF
  • Stock: 898
  • Description: 1.8μs, 1ns SPDT 2Ohm DUAL Analog Switches MAX14763 250nA 5V 8-WDFN Exposed Pad(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Contact Plating Tin
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 8-WDFN Exposed Pad
Number of Pins 8
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2012
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 8
ECCN Code EAR99
Resistance 2Ohm
Max Power Dissipation 1.9512W
Technology BICMOS
Terminal Position DUAL
Number of Functions 1
Supply Voltage 5V
Terminal Pitch 0.65mm
Base Part Number MAX14763
Operating Supply Voltage 5V
Polarity Non-Inverting
Number of Channels 1
Number of Circuits 1
Max Supply Voltage 5.5V
Min Supply Voltage 3V
Analog IC - Other Type SPST
Operating Supply Current 4.1mA
Supply Type Single
-3db Bandwidth 100MHz
On-State Resistance (Max) 2Ohm
High Level Output Current 250mA
Multiplexer/Demultiplexer Circuit 2:1
Off-state Isolation-Nom 77 dB
Current - Leakage (IS(off)) (Max) 250nA
On-state Resistance Match-Nom 0.0051Ohm
Switch Circuit SPDT
Switch Time (Ton, Toff) (Max) 1.8μs, 1ns
Charge Injection 1370pC
Channel-to-Channel Matching (ΔRon) 5.1m Ω
Crosstalk -83dB @ 100kHz
Voltage - Supply, Single (V+) 3V~5.5V
Length 3mm
Radiation Hardening No
RoHS Status ROHS3 Compliant

MAX14763ETA+T Overview


The electronic part can be shipped overseas conveniently because it is packaged in 8-WDFN Exposed Pad. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. Multiplexer and demultiplexer circuits have a number 2:1. The operating temperature is extended to around -40°C~85°C TA. 8 terminations have been made so far. The electronic part provides high-quality output because it has 1 channels. Powered by a 5V voltage supply, the electrical part should be switched on and run. Based on SPDT switching circuits, these analog multiplexers work. Circuits number 1 make up this analogue multiplexer. MAX14763 can be used to search for analog multiplexer variants. It has an internal resistance of 2Ohm. For functions related to 8 pins, please refer to the datasheets. A voltage higher than 5.5V should not normally be supplied to the switches. A cost-effective Single supply type analogue multiplexer. It is recommended to use 3V as the lowest voltage for the electrical part. This multiplexer would work with 4.1mA current. Using a single voltage supply, this switch device consumes 3V~5.5V volts. This product is integrated with an analog integrated circuit (IC) of type SPST. There is a voltage range of 5V operating voltages for the electrical part.

MAX14763ETA+T Features


1 Channels
Switch Circuit: SPDT
4.1mA Supply Current
-3db Bandwidth: 100MHz

MAX14763ETA+T Applications


There are a lot of Maxim Integrated MAX14763ETA+T Analog Switches & Multiplexers ICs applications.

  • Cell phones
  • Cable Telephony – NIU, Set-Top Box, Home Side Box
  • Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
  • Channelized and Unchannelized DS3 applications
  • Data Acquisition Systems
  • Power routing
  • Microprocessor controlled systems
  • Video switching
  • Residential Gateways, Home Gateway/Router
  • Medical

Write a review

Note: HTML is not translated!
    Bad           Good