MAX16010TAC+T
| Parameters | |
|---|---|
| Min Supply Voltage | 5.5V |
| Operating Supply Current | 25μA |
| Adjustable Threshold | YES |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | Adjustable/Selectable |
| Number of Voltages Monitored | 2 |
| Reset Timeout | <1ms Minimum |
| Supply Current-Max (Isup) | 0.04mA |
| Undervoltage Threshold | 1.12V |
| Overvoltage Threshold | 1.18V |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-WDFN Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Multi-Voltage Supervisor |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 1.455W |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 14V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX16010 |
| Output | Open Drain or Open Collector |
| Pin Count | 8 |
| Power Supplies | 14V |
| Number of Channels | 1 |
| Max Supply Voltage | 72V |
MAX16010TAC+T Overview
There are 8 terminals on this power management that allow it to be mounted. This power ic is packaged in a way that looks like a Tape & Reel (TR). In this IC power you will find 1 functions for you to refer to. On this supervisor, there is a series of 1 channels that can be found. In this PMIC, you can find 8-WDFN Exposed Pad functions for your reference. Several of the benefits of this PMIC are also shared by other Multi-Voltage Supervisor products. According to the specification, the package's peak reflow temperature is specified to be 260. IC management conducts in a 14V-voltage supply. Power management conducts at a voltage of 2. Surface Mount mounts power management on the wall. The power management system can be categorized as a Power Management Circuits chip. The total number of pins on this power management is 8. There are 8 pins on the power managment ic. It is recommended that the minimum supply voltage (Vsup) for this IC management should not be less than 5.5V volts. Voltage (Vsup) shouldn't exceed 72V volts in this PMIC. Power management recommends the Surface Mount mounting type. The temperature of the supervisors should be set to this range: -40°C~125°C TA. When this power management system is in operation, it produces an output voltage of Open Drain or Open Collector. Supplied with a operating current of 25μA, this PMIC is capable of fully function as specified. A similar IC managements number of the manufacturer can always be found by using MAX16010, the base power ics number. The power management must be powered by 14V volts to function properly.
MAX16010TAC+T Features
Multi-Voltage Supervisor type
Minimum supply voltage of 5.5V
25μA operating supply current
MAX16010TAC+T Applications
There are a lot of Maxim Integrated MAX16010TAC+T Voltage Supervisors applications.
- Refrigeration
- Insulation fault location system
- Power distribution systems of ICU
- Sensitive sensors
- Stable power system
- Electronics installed in the vehicle
- Personal computers
- Leakage current detection
- Consumer electronics
- DSP
