MAX16037LLA31+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-WFDFN |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | GOLD |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 380.6mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Terminal Pitch | 0.5mm |
| Base Part Number | MAX16037 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Power Supplies | 2.5/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 0V |
| Operating Supply Current | 22μA |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 3.08V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.05mA |
| Min Reset Threshold Voltage | 3V |
| Max Reset Threshold Voltage | 3.15V |
| Undervoltage Threshold | 3V |
| Overvoltage Threshold | 3.15V |
| Length | 2mm |
| Width | 2mm |
| RoHS Status | ROHS3 Compliant |
MAX16037LLA31+T Overview
As far as the mounting terminals of this voltage supervisor are concerned, it has 8 in total. This power ic is packaged in a way that looks like a Tape & Reel (TR). There are 1 functions included in this PMIC so that you can refer to them. Depending on the power managment ic you are looking at, you can find a total of 1 channels. The purpose of this IC power is to provide you with a reference of 8-WFDFN functions. There are a lot of similarities between this IC power and other Battery Backup Circuit products. The package peak reflow temperature is specified to be 260. During operation, the power ic is supplied with a voltage of 1. Using Surface Mount, IC management is mounted. In this case, this PMIC chip can be sub-categorized as a Power Management Circuits chip. Power management has a total of 8 pins. Power managment ic pin count is 8. I should note that the minimum supply voltage (Vsup) for this IC management should be at least 0V, which is the minimum supply voltage that should be applied. The maximum supply voltage (Vsup) in this PMIC should not exceed 5.5V volts. The recommended mounting type for IC management is Surface Mount. The supervisors should be set to the following temperature: -40°C~85°C TA. During operation, this power management system outputs Push-Pull, Totem Pole. The supply current of the power management is 22μA. If you want to search for similar IC managements of this manufacturer, you can always refer to MAX16037, which is the base power ics number. It requires 2.5/5V watts of power to operate this voltage supervisor.
MAX16037LLA31+T Features
Battery Backup Circuit type
Minimum supply voltage of 0V
22μA operating supply current
MAX16037LLA31+T Applications
There are a lot of Maxim Integrated MAX16037LLA31+T Voltage Supervisors applications.
- Radar
- FPGA design
- Network equipment
- Medical-specific isolation transformer
- Solar power charger
- Efficient information transmission
- Important electronics for automotive protection
- Display equipment
- Insulation fault location system
- Radio
