MAX16043TG+
| Parameters | |
|---|---|
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-WFQFN Exposed Pad |
| Number of Pins | 24 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | Sequencer |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 2.222W |
| Technology | BICMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX16043 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 24 |
| JESD-30 Code | S-XQCC-N16 |
| Number of Channels | 4 |
| Max Supply Voltage | 28V |
| Min Supply Voltage | 2.2V |
| Operating Supply Current | 52μA |
| Adjustable Threshold | YES |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 9 Selectable Threshold Combinations |
| Number of Voltages Monitored | 4 |
| Reset Timeout | 140ms/Adjustable Minimum |
| Supply Current-Max (Isup) | 0.08mA |
| Height Seated (Max) | 0.8mm |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
MAX16043TG+ Overview
There are 16 terminals on this power management that allow it to be mounted. A Tube package is used to package the power management. In this PMIC, you can find 1 functions for your reference. There are 4 channels on this power managment ic that can be found in a series. IC management is packaged as a 24-WFQFN Exposed Pad package. As with other Sequencer products, this IC management also offers a wide range of benefits. Specifies a reflow peak temperature of 260 for the package during reflow. The supervisor is always powered by a 3.3V volt supply. When 4 is applied to the power ic, it conducts. By Surface Mount, IC management has been mounted. The power management system can be categorized as a Power Management Circuits chip. A total of 24 pins are located on this power management. Power managment ic pin count is 24. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 2.2V. The maximum supply voltage (Vsup) is not to exceed 28V volts in this IC management. Surface Mount mounting is recommended. We recommend setting the supervisors to -40°C~125°C TA degrees. When this power management system is in operation, it produces an output voltage of Push-Pull, Totem Pole. Supplied with a operating current of 52μA, this PMIC is capable of fully function as specified. It is always advisable to use MAX16043, the base supervisor number, when searching for similar PMICs from the manufacturer.
MAX16043TG+ Features
Sequencer type
Minimum supply voltage of 2.2V
52μA operating supply current
MAX16043TG+ Applications
There are a lot of Maxim Integrated MAX16043TG+ Voltage Supervisors applications.
- Electrical fire monitoring system
- DSP
- Power distribution systems of ICU
- Automotive permanent magnet synchronous motors
- Cloud computing
- Important electronics for automotive protection
- Leakage protection
- Automotive power systems
- Precision measurement
- Insulation fault location system
