MAX16055DAUB+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Published | 2009 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Type | Multi-Voltage Supervisor |
| Additional Feature | MANUAL RESET INPUT |
| HTS Code | 8542.39.00.01 |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 444mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.5mm |
| Base Part Number | MAX16055 |
| Output | Open Drain or Open Collector |
| Pin Count | 10 |
| Operating Supply Voltage | 3.3V |
| Number of Channels | 6 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 55μA |
| Nominal Supply Current | 55μA |
| Adjustable Threshold | YES |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 6 Selectable Threshold Combinations |
| Number of Voltages Monitored | 6 |
| Reset Timeout | 140ms Minimum |
| Undervoltage Threshold | 500mV |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Width | 3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
MAX16055DAUB+ Overview
Power management is mounted through 10 terminals. There is a Tube-packaging method applied to IC management. Power management is possible to find a series of 1 functions. Depending on the power managment ic you are looking at, you can find a total of 6 channels. For your reference, this PMIC includes a list of 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) functions. With power management, you get a lot of benefits that you won't find in other Multi-Voltage Supervisor products. A supply voltage of 3.3V is used to conduct the PMIC chip. Power ics operate at 6 supply voltages. Using Surface Mount, IC management is mounted. The power management belongs to the Power Management Circuits subcategory. A total of 10 pins are located on this power management. Power managment ic pin count is 10. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 1V. There should be no more than 5.5V volts of supply voltage (Vsup) in this power management. Power management recommends the Surface Mount mounting type. We recommend setting the supervisors to -40°C~125°C TA degrees. As this power managment ic operates, it is able to produce an output voltage of Open Drain or Open Collector. There is a supply current of 55μA for the power management. Additionally, there are many other features that can be found inside of the power management, such as [0]. It is always advisable to use MAX16055, the base supervisor number, when searching for similar PMICs from the manufacturer.
MAX16055DAUB+ Features
Multi-Voltage Supervisor type
Minimum supply voltage of 1V
55μA operating supply current
MAX16055DAUB+ Applications
There are a lot of Maxim Integrated MAX16055DAUB+ Voltage Supervisors applications.
- Military electronics
- Embedded computing
- Analog circuit
- Refrigeration
- Detection of phase loss
- Utility meter
- Stable power system
- Insulation fault location system
- Battery-powered equipment
- Medical-specific insulation monitor
