MAX16058ATA31+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-WDFN Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 1.95W |
| Technology | BICMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX16058 |
| Output | Open Drain or Open Collector |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.1V |
| Operating Supply Current | 125nA |
| Nominal Supply Current | 125nA |
| Adjustable Threshold | YES |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 3.075V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | Adjustable/Selectable |
| Min Reset Threshold Voltage | 2.998V |
| Max Reset Threshold Voltage | 3.152V |
| Undervoltage Threshold | 2.998V |
| Overvoltage Threshold | 3.152V |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | ROHS3 Compliant |
MAX16058ATA31+T Overview
A total of 8 terminals are used to mount this power management. Packaged in the form of a Tape & Reel (TR), power management is easy to use. In this PMIC, you can find 1 functions for your reference. On this supervisor, there is a series of 1 channels that can be found. Please find attached 8-WDFN Exposed Pad functions for your reference in this IC power. There are many benefits that this IC power shares with other Simple Reset/Power-On Reset products as well. In order to ensure a good reflow performance, the package peak reflow temperature must be set at NOT SPECIFIED. A supply voltage of 1.8V is used to conduct the PMIC chip. When 1 is applied to the power ic, it conducts. By Surface Mount, IC management has been mounted. It is possible to subcategorize this power ic as a Power Management Circuits chip. In total, IC powers are 8 pins on the board. This power management has 8 pins. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 1.1V. The supply voltage (Vsup) should not exceed 5.5V volts in this IC power. The recommended mounting type for IC management is Surface Mount. It is recommended to set the supervisor's temperature to this range: -40°C~125°C TA. As a result of this supervisor's operation, the output voltage is Open Drain or Open Collector. There is a supply current of 125nA for the power management. You can always use MAX16058, the base supervisor number, to search for similar PMICs of the manufacturer.
MAX16058ATA31+T Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.1V
125nA operating supply current
MAX16058ATA31+T Applications
There are a lot of Maxim Integrated MAX16058ATA31+T Voltage Supervisors applications.
- Automotive power systems
- Leakage protection
- Medical-specific isolation transformer
- Network equipment
- Medical-specific insulation monitor
- External alarm
- Utility meter
- emergency room
- Insulation fault location system
- Consumer electronics
