MAX16062ETG+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-WFQFN Exposed Pad |
| Number of Pins | 24 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Published | 2008 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| ECCN Code | EAR99 |
| Type | Multi-Voltage Supervisor |
| Additional Feature | MANUAL RESET INPUT |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 1.67W |
| Technology | BICMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX16062 |
| Output | Open Drain or Open Collector |
| Pin Count | 24 |
| Qualification Status | Not Qualified |
| Power Supplies | 2.5/5V |
| Number of Channels | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 45μA |
| Adjustable Threshold | YES |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 8 Selectable Threshold Combinations |
| Number of Voltages Monitored | 8 |
| Reset Timeout | 140ms/Adjustable Minimum |
| Supply Current-Max (Isup) | 0.07mA |
| Length | 4mm |
| Width | 4mm |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
MAX16062ETG+ Overview
As you can see, this power management is mounted through 24 terminals. In terms of packaging, power management follows the Tube model. Please refer to this PMIC for 1 functions. A series of 8 channels can be found on this supervisor. There are 24-WFQFN Exposed Pad functions included in this PMIC so that you can refer to them. With power management, you get a lot of benefits that you won't find in other Multi-Voltage Supervisor products. In order to ensure a good reflow performance, the package peak reflow temperature must be set at NOT SPECIFIED. Manage ics operate at 3.3V supply voltages. There is a voltage supply of 8 for the PMIC chip, and the chip conducts at that voltage. Surface Mount mounts IC management. In this case, this PMIC chip can be sub-categorized as a Power Management Circuits chip. In total, IC powers are 24 pins on the board. 24 pins are present on the power management system. It is recommended that the minimum supply voltage (Vsup) for this IC management should not be less than 1V volts. There should be no more than 5.5V volts of maximum supply voltage (Vsup) in this power management. The recommended mounting type is Surface Mount. The supervisors should be set to the following temperature: -40°C~125°C TA. While in operation, this supervisor has a voltage output of Open Drain or Open Collector. For this power management, there is an 45μA volt supply current. There are also other features in the software such as [0], just to mention a few. If you want to search for similar IC managements of this manufacturer, you can always refer to MAX16062, which is the base power ics number. It requires 2.5/5V watts of power to operate this voltage supervisor.
MAX16062ETG+ Features
Multi-Voltage Supervisor type
Minimum supply voltage of 1V
45μA operating supply current
MAX16062ETG+ Applications
There are a lot of Maxim Integrated MAX16062ETG+ Voltage Supervisors applications.
- Microcontroller system
- Data storage applications
- Power distribution systems of CCU
- Detection of phase sequence
- Utility meter
- Satellite navigation
- Medical-specific insulation monitor
- Analog circuit
- Embedded computing
- Network equipment
