MAX1693EUB
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1998 |
| JESD-609 Code | e0 |
| Feature | Status Flag |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Resistance | 90mOhm |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 444mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Base Part Number | MAX1693 |
| Pin Count | 10 |
| Number of Outputs | 1 |
| Output Type | P-Channel |
| Max Output Current | 1A |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Interface | On/Off |
| Analog IC - Other Type | POWER SUPPLY SUPPORT CIRCUIT |
| Operating Supply Current | 25μA |
| Current - Output (Max) | 700mA |
| Nominal Supply Current | 14μA |
| Output Configuration | High Side |
| Power Dissipation | 444mW |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Adjustable Threshold | NO |
| Input Type | Non-Inverting |
| Turn On Delay Time | 200 μs |
| Switch Type | USB Switch |
| Min Input Voltage | 2.7V |
| Max Input Voltage | 5.5V |
| Supply Type | Single |
| Turn-Off Delay Time | 20 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 2.7V~5.5V |
| Fault Protection | Current Limiting (Fixed), Over Temperature |
| Rds On (Typ) | 60m Ω |
| Height | 950μm |
| Length | 3.05mm |
| Width | 3.05mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX1693EUB Overview
A Tube is used to package it.In the 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) package, it is included.The lighting driver has the mounting type Surface Mount.There is a switch type of USB Switch.To ensure reliable operation, set the temperature to -40°C~85°C TA.By default, it is set to output 1.The LED driving board is powered by a voltage of Not Required.It has a maximum output voltage of P-Channel volts.It has a total of Status Flag features.This object belongs to the MAX1693 family.It contains 10 terminations.In order to operate, 10 pins are used.As far as functions are concerned, the lighting driver has 1.This LED driver has a maximum output of 700mAV.To meet the operation criteria, the maximum output current drops to 1A.A supply voltage of 5V leads to high efficiency.As a result, it is mounted in the manner of Surface Mount.As a result, it has a total of 10 pins.In this case, there is 90mOhm resistance in the LED driving board.A self-contained LED driver with a capacity of Power Management Circuits is contained in an econtainer.The gadget uses an analog IC, which is POWER SUPPLY SUPPORT CIRCUIT in this case.In total, 1 channels are available.It has a power supply of 5V.This LED driver can handle voltages up to 5.5V volts.There is a minimum input voltage of 2.7V volts for this LED driver.
MAX1693EUB Features
Supplied from 5V
Resistance of 90mOhm
1 channels
MAX1693EUB Applications
There are a lot of Maxim Integrated MAX1693EUB Power Switches ICs applications.
- PC Card Hot Swap
- Hard Disk Drives
- Low Voltage I/O System Power
- Wireless Modem Data Cards
- Smart Phones, Feature Phones
- Portable GPS Device
- Portable/Handheld Devices
- Solid State Drivers
- HDD and SSD
- Portable Music Players
