MAX203CPP
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 20 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 1997 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Additional Feature | INTERNAL CHARGE PUMP |
| HTS Code | 8542.39.00.01 |
| Subcategory | Line Driver or Receivers |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX203 |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Power Supplies | 5V |
| Supply Current-Max | 15mA |
| Data Rate | 120Kbps |
| Output Characteristics | TOTEM-POLE |
| Differential Output | NO |
| Output Polarity | INVERTED |
| Protocol | RS232 |
| Input Characteristics | SCHMITT TRIGGER |
| Number of Drivers/Receivers | 2/2 |
| Driver Number of Bits | 2 |
| Receiver Number of Bits | 2 |
| Duplex | Full |
| Receiver Hysteresis | 500mV |
| Interface Standard | EIA-232-E; TIA-232-E; V.28 |
| Receive Delay-Max | 10000 ns |
| Output Low Current-Max | 0.0016A |
| Out Swing-Min | 10 V |
| Height Seated (Max) | 4.572mm |
| Length | 26.16mm |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX203CPP Overview
LED drivers with the enhanced 20-DIP (0.300, 7.62mm) package will be able to drive a variety of common LEDs with ease.The receiver is packaged in a Tube package.Since this part is a Transceiver can transceiver, a number of solutions have been able to utiliTransceivere it for various purposes.This wide receiver can be placed on any Through Hole-type PCB or development board.This differential driver uses 4.75V~5.25V for power supply.There can be up to 2/2 eligible receivers/drivers on the field at the same time with this electronic part.The operating temperature of this ic receiver is 0°C~70°C. It is primarily designed for applications with low temperatures.With a supply voltage range of 5V, this line driver ic operates efficiently.In this wide receiver, 20 terminations are integrated for driving and receiving signals from data.ICs that are packaged with market standard pinouts are available on the market.Since the part number MAX203 represents the product type, temperature, package, etc., you can try searching with that number to find more variants.An enhanced power dissipation driver IC with 20 pins.In terms of resolution, this ic receiver was capable of providing a 2-bit resolution.As a rule of thumb, this receiver is typically specified with a resolution of 2 bits.There is a subcategory named Line Driver or Receivers for this rf transceiver module.Driver ICs such as this one are designed to operate from 5V power sources.A INTERNAL CHARGE PUMP function is also included on this optical transceiver module, which improves the overall signal management accuracy and stability.It is recommended that enough current be supplied to the VCC pin of the ic receiver, but not more than 15mA.
MAX203CPP Features
Tube package
20 pin count
20 pins
5V power supply
MAX203CPP Applications
There are a lot of Maxim Integrated MAX203CPP Drivers/Receivers/Transceivers applications.
- Shortwave receiver
- Datacom networking applications
- Single to Multimode Fiber Conversion
- Wireless communication
- Wired telephone
- Carrier phase observations
- Servers
- Wireless multimedia center in smart home
- Switches
- Routers
