MAX208IDBG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 24 |
| Weight | 172.39345mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Line Driver or Receivers |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX208 |
| Pin Count | 24 |
| Output Voltage | 9V |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Nominal Supply Current | 20mA |
| Propagation Delay | 2 μs |
| Logic Function | Receiver, Transceiver |
| Data Rate | 120Kbps |
| Differential Output | NO |
| Protocol | RS232 |
| Input Characteristics | SCHMITT TRIGGER |
| Number of Drivers/Receivers | 4/4 |
| Receiver Number of Bits | 4 |
| Duplex | Full |
| Receiver Hysteresis | 500mV |
| Interface Standard | EIA-232-F; TIA-232-F; V.28 |
| Number of Drivers | 4 |
| Number of Transceivers | 1 |
| Simplex/Duplex | Full Duplex |
| Supply Voltage1-Nom | 5V |
| Drain to Source Resistance | 2Ohm |
| High Level Input Current-Max | 0.0002A |
| Height | 2mm |
| Length | 8.2mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX208IDBG4 Overview
This LED driver IC features an enhanced 24-SSOP (0.209, 5.30mm Width) package for driving common LEDs.Tube package is used to mount this receiver.Several solutions have used this Transceiver can transceiver in a variety of applications due to its Transceiver IC nature.On any Surface Mount-type PCB or development board, you can install this wide receiver.This differential driver requires a 4.5V~5.5V power supply.At any one time, this electronic part can have up to 4/4 eligible receivers/drivers.IC receiver likes this one are designed for use in applications where operating temperatures are -40°C~85°C.There is a voltage range of 5V for this line driver ic, so it can operate efficiently.This wide receiver has 24 terminations for driving and receiving data signals.ICs that are packaged with market standard pinouts are available on the market.As the base part number MAX208 identifies the product type, temperature, package, etc., you can try searching with it to get more variants of this part.24-pin driver IC with improved power dissipation control.Package size is drastically reduced by downsizing ICs and mounting them in high-density Surface Mount arrays.As a rule of thumb, this receiver is typically specified with a resolution of 4 bits.There is a supply voltage of 5V on the input of this transceiver module, so it can be operated from that source.This rf transceiver module can be grouped into a subcategory named Line Driver or Receivers.Driver ICs such as this one are designed to operate from 5V power sources.In total, there are 1 transceivers implemented by this module isolated transceiver.The integrator circuit comes with embedded 4 drivers.Voltage can be delivered at 9V by Wide receiver.
MAX208IDBG4 Features
Tube package
24 pin count
24 pins
5V power supply
MAX208IDBG4 Applications
There are a lot of Texas Instruments MAX208IDBG4 Drivers/Receivers/Transceivers applications.
- Servers
- Single to Multimode Fiber Conversion
- Military satellite communications
- Remote controls
- Satellite radio receiver
- Car alarm systems
- Wireless showroom
- Point-to-point networking
- High-speed computer links
- Low power, low voltage systems
