MAX211CWI
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 28-SOIC (0.295, 7.50mm Width) |
| Surface Mount | YES |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 1997 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Additional Feature | TRISTATABLE RECEIVERS; EXTERNAL CHARGE PUMP |
| HTS Code | 8542.39.00.01 |
| Subcategory | Line Driver or Receivers |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX211 |
| Pin Count | 28 |
| JESD-30 Code | R-PDSO-G28 |
| Qualification Status | Not Qualified |
| Power Supplies | 5V |
| Data Rate | 120Kbps |
| Output Characteristics | 3-STATE |
| Differential Output | NO |
| Output Polarity | INVERTED |
| Protocol | RS232 |
| Input Characteristics | SCHMITT TRIGGER |
| Number of Drivers/Receivers | 4/5 |
| Driver Number of Bits | 4 |
| Receiver Number of Bits | 5 |
| Duplex | Full |
| Receiver Hysteresis | 500mV |
| Interface Standard | EIA-232-E; TIA-232-E; V.28 |
| Receive Delay-Max | 10000 ns |
| Output Low Current-Max | 0.0016A |
| Out Swing-Min | 10 V |
| Height Seated (Max) | 2.65mm |
| Length | 17.9mm |
| Width | 7.5mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX211CWI Overview
This LED driver IC features an enhanced 28-SOIC (0.295, 7.50mm Width) package for driving common LEDs.The Tube package houses this receiver.The Transceiver can transceiver type enables this part to be used in a wide range of applications.Ideally, you should place this wide receiver on a Surface Mount-type PCB or development board.A differential driver like this uses 4.5V~5.5V of power.The field can have up to 4/5 eligible receivers/drivers at once when using this electronic part.IC receiver is designed for applications with a temperature of 0°C~70°C.With a voltage range of 5V, this driver IC can operate efficiently.The integrated terminations of this wide receiver allow it to drive and receive signals from data.Transceiver comes with 28 standard pinouts that meet the market's requirements.The base part number MAX211 identifies the product type, temperature, package, etc., so you can search for more variants by using it.An important feature of this ic receiver was its 4-bit resolution capability.There are typically 5 bits of resolution specified in the specifications of this receiver.A subcategory named Line Driver or Receivers can be used to group this rf transceiver module.It is designed to be operated from a 5V power supply, so the module isolated transceiver will work effectively.Additionally, this optical transceiver module features the TRISTATABLE RECEIVERS; EXTERNAL CHARGE PUMP function, which improves the stability and accuracy of signal management in general.
MAX211CWI Features
Tube package
28 pin count
5V power supply
MAX211CWI Applications
There are a lot of Maxim Integrated MAX211CWI Drivers/Receivers/Transceivers applications.
- Automation systems
- Telecom applications
- transmission relay
- Cordless telephone
- Transmission stations
- Satellite radio receiver
- IP cameras
- Fast Ethernet
- Wireless projection application for conferences
- Aircraft positioning
