MAX213ECAI+
| Parameters | |
|---|---|
| Out Swing-Min | 10 V |
| Height Seated (Max) | 1.99mm |
| Length | 10.2mm |
| Width | 5.29mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 28-SSOP (0.209, 5.30mm Width) |
| Surface Mount | YES |
| Number of Pins | 28 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Matte Tin (Sn) |
| HTS Code | 8542.39.00.01 |
| Subcategory | Line Driver or Receivers |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX213 |
| Pin Count | 28 |
| Qualification Status | Not Qualified |
| Power Supplies | 5V |
| Supply Current-Max | 20mA |
| Data Rate | 120Kbps |
| Output Characteristics | 3-STATE |
| Differential Output | NO |
| Output Polarity | INVERTED |
| Protocol | RS232 |
| Input Characteristics | SCHMITT TRIGGER |
| Number of Drivers/Receivers | 4/5 |
| Driver Number of Bits | 4 |
| Receiver Number of Bits | 5 |
| Duplex | Full |
| Receiver Hysteresis | 500mV |
| Receive Delay-Max | 40000 ns |
| Output Low Current-Max | 0.0016A |
MAX213ECAI+ Overview
With the enhanced 28-SSOP (0.209, 5.30mm Width) package, this driver IC is excellent for driving common LEDs.The Tube package houses this receiver.Several solutions have used this Transceiver can transceiver in a variety of applications due to its Transceiver IC nature.Ideally, you should place this wide receiver on a Surface Mount-type PCB or development board.Power supply for this differential driver is 4.5V~5.5V.As many as 4/5 receivers/drivers are eligible for use on this electronic part.This ic receiver has been primarily designed for applications where the operating temperature is 0°C~70°C.5V is the supply voltage range that this line driver ic can efficiently operate with.In order to drive and receive signals from data, this wide receiver has 28 terminations integrated.The pinouts for this transceiver are standardized to meet the needs of the market.The base part number MAX213 identifies the product type, temperature, package, etc., so you can search for more variants by using it.28-pin driver IC with improved power dissipation control.An important feature of this ic receiver was its 4-bit resolution capability.In most cases, the receiver will be specified with a 5-bit resolution.An additional subcategory named Line Driver or Receivers can be created for this rf transceiver module.Driver ICs such as this one are designed to operate from 5V power sources.Ensure that the VCC pin of the ic receiver receives sufficient but not more than 20mA of input current.
MAX213ECAI+ Features
Tube package
28 pin count
28 pins
5V power supply
MAX213ECAI+ Applications
There are a lot of Maxim Integrated MAX213ECAI+ Drivers/Receivers/Transceivers applications.
- Ethernet circuitry
- Satellite radio receiver
- Wireless showroom
- transmission relay
- AV receiver
- Servers
- Structural bonding
- Notebook
- Long-distance fiber optic network applications
- Interconnection between switches and computers
