MAX218CAP+
| Parameters | |
|---|---|
| Duplex | Full |
| Receiver Hysteresis | 100mV |
| Interface Standard | EIA-232-E; V.24; V.28; EIA-562 |
| Receive Delay-Max | 700 ns |
| Transmit Delay-Max | 2700 ns |
| Output Low Current-Max | 0.001A |
| Out Swing-Min | 5 V |
| Height Seated (Max) | 1.99mm |
| Length | 7.2mm |
| Width | 5.29mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Surface Mount | YES |
| Number of Pins | 20 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Tin (Sn) |
| HTS Code | 8542.39.00.01 |
| Subcategory | Line Driver or Receivers |
| Technology | CMOS |
| Voltage - Supply | 1.8V~4.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX218 |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Power Supplies | 3V |
| Supply Current-Max | 3mA |
| Data Rate | 120Kbps |
| Output Characteristics | 3-STATE |
| Differential Output | NO |
| Output Polarity | INVERTED |
| Protocol | RS232 |
| Input Characteristics | SCHMITT TRIGGER |
| Number of Drivers/Receivers | 2/2 |
| Driver Number of Bits | 2 |
| Receiver Number of Bits | 2 |
MAX218CAP+ Overview
Due to the enhanced 20-SSOP (0.209, 5.30mm Width) package, this driver IC is excellent for driving common LEDs.The Tube package contains this receiver.With its Transceiver can transceiver design, this part can be incorporated into a wide range of solutions.A Surface Mount-type PCB or development board can be used to place this wide receiver.It takes 1.8V~4.25V from the power supply to run this differential driver.Up to 2/2 receivers/drivers can be installed simultaneously on this electronic part.As its name implies, this ic receiver is designed for applications where 0°C~70°C is the operating temperature.An output voltage range of 3V is sufficient to run this line driver ic efficiently.There are 20 terminations in this wide receiver so that signals can be driven from the data and received.As a standard package, this transceiver comes with a 20-pin layout that follows the market standard.For more variants of this part, try searching with the base part number MAX218, which indicates the product type, temperature, package, etc.An enhanced power dissipation control is provided by this 20-pin driver IC.Using this ic receiver, you were able to achieve a resolution of 2 bits.As a rule of thumb, this receiver is typically specified with a resolution of 2 bits.It is possible to subcategoriLine Driver or Receiverse this rf transceiver module as Line Driver or Receivers.Driver ICs such as this one are designed to operate from 3V power sources.A sufficient amount of input current should be provided to the optical transceiver module's VCC pin, but not more than 3mA.
MAX218CAP+ Features
Tube package
20 pin count
20 pins
3V power supply
MAX218CAP+ Applications
There are a lot of Maxim Integrated MAX218CAP+ Drivers/Receivers/Transceivers applications.
- Bridges
- Copper connection network
- Indoor ad hoc meeting
- Wireless interactive experience
- Fiber optic cable connection network
- Car radio
- Notebook
- Wireless projection application for business talks
- IPTV front end
- Ship
