MAX232AEPE
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Additional Feature | EXTERNAL CHARGE PUMP |
| Subcategory | Line Driver or Receivers |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX232 |
| Pin Count | 16 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Number of Channels | 2 |
| Interface | RS-232 |
| Number of I/O | 8 |
| Nominal Supply Current | 10mA |
| Propagation Delay | 1 μs |
| Logic Function | Receiver, Transceiver |
| Data Rate | 200kbps |
| Output Characteristics | TOTEM-POLE |
| Differential Output | NO |
| Output Polarity | INVERTED |
| Protocol | RS232 |
| Input Characteristics | SCHMITT TRIGGER |
| Number of Drivers/Receivers | 2/2 |
| Driver Number of Bits | 2 |
| Receiver Number of Bits | 2 |
| Duplex | Full |
| Receiver Hysteresis | 500mV |
| Number of Transceivers | 1 |
| Transmit Delay-Max | 3500 ns |
| High Level Input Current-Max | 0.00004A |
| Height | 4.572mm |
| Length | 19.43mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX232AEPE Overview
LED drivers with the enhanced 16-DIP (0.300, 7.62mm) package will be able to drive a variety of common LEDs with ease.Tube package is used to mount this receiver.Several solutions have used this Transceiver can transceiver in a variety of applications due to its Transceiver IC nature.Ideally, you should place this wide receiver on a Through Hole-type PCB or development board.With respect to the power supply, this differential driver uses 4.5V~5.5V.This electronic part can have?up to 2/2 eligible receivers/drivers on the field at once.?In most applications, this ic receiver is used in environments where -40°C~85°C is the operating temperature.Driver ICs in this category can operate efficiently with a supply voltage range of 5V.Wide receiver has 16 terminations built in for driving or receiving signals from data.It is packaged with 16 pinouts that are market standard for this particular transceiver.For more variants of this part, try searching with the base part number MAX232, which indicates the product type, temperature, package, etc.16-pin driver chip with enhanced power dissipation.Package size is drastically reduced by downsizing ICs and mounting them in high-density Through Hole arrays.An important feature of this ic receiver was its 2-bit resolution capability.It is typical for this receiver to have a resolution of 2 bits when it is specified.This transceiver module is designed to operate from an input voltage supply of 5V.Line Driver or Receivers is a subcategory of this rf transceiver module.Driver ICs such as this one are designed to operate from 5V power sources.ICs implement a total of 1 transceivers.The EXTERNAL CHARGE PUMP function of this optical transceiver module improves the overall stability and accuracy of signal management.An IC with 8 standard serial inputs and outputs, this is a great IC to use.There are a total of 2 channels embedded in this optical transceiver.
MAX232AEPE Features
Tube package
16 pin count
16 pins
5V power supply
2 channels
MAX232AEPE Applications
There are a lot of Maxim Integrated MAX232AEPE Drivers/Receivers/Transceivers applications.
- IPTV front end
- Wireless showroom
- Wireless HD Photography
- Ship
- Single to Multimode Fiber Conversion
- Wireless transmission
- Aircraft navigation
- Data center
- Changeing the frequency from IF to RF
- Switches
