MAX232ECPE
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Additional Feature | EXTERNAL CHARGE PUMP |
| HTS Code | 8542.39.00.01 |
| Subcategory | Line Driver or Receivers |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX232 |
| Pin Count | 16 |
| JESD-30 Code | R-PDIP-T16 |
| Qualification Status | Not Qualified |
| Power Supplies | 5V |
| Power Dissipation | 755mW |
| Supply Current-Max | 10mA |
| Data Rate | 120Kbps |
| Output Characteristics | TOTEM-POLE |
| Differential Output | NO |
| Output Polarity | INVERTED |
| Protocol | RS232 |
| Input Characteristics | SCHMITT TRIGGER |
| Number of Drivers/Receivers | 2/2 |
| Driver Number of Bits | 2 |
| Receiver Number of Bits | 2 |
| Duplex | Full |
| Receiver Hysteresis | 500mV |
| Interface Standard | EIA-232-E; TIA-232-E; V.28 |
| Receive Delay-Max | 10000 ns |
| Output Low Current-Max | 0.0032A |
| Out Swing-Min | 10 V |
| High Level Input Current-Max | 0.0002A |
| Height Seated (Max) | 4.572mm |
| Length | 19.175mm |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX232ECPE Overview
This LED driver IC features an enhanced 16-DIP (0.300, 7.62mm) package for driving common LEDs.Tube package is used for this receiver.The Transceiver can transceiver technology has enabled this part to power many solutions for a variety of uses.Ideally, you should place this wide receiver on a Through Hole-type PCB or development board.A differential driver like this uses 4.5V~5.5V of power.As many as 2/2 receivers/drivers are eligible for use on this electronic part.Applications with operating temperatures of 0°C~70°C have been designed primarily for this ic receiver.Driver ICs with a supply voltage range of 5V can operate efficiently.This wide receiver has 16 terminations for driving and receiving data signals.It is packaged with 16 pinouts that are market standard for this particular transceiver.As the base part number MAX232 identifies the product type, temperature, package, etc., you can try searching with it to get more variants of this part.In this ic receiver, the resolution was able to be set to a maximum of 2 bits.This receiver is typically specified with a resolution of 2 bits. There is a subcategory called Line Driver or Receivers for this rf transceiver module.IC5V is a high performance driver IC designed to work with a 5V power supply.The EXTERNAL CHARGE PUMP function of this optical transceiver module improves the overall stability and accuracy of signal management.There should be enough current supplied to the VCC pin of the part, but not more than 10mA.
MAX232ECPE Features
Tube package
16 pin count
5V power supply
MAX232ECPE Applications
There are a lot of Maxim Integrated MAX232ECPE Drivers/Receivers/Transceivers applications.
- Satellite communications networks
- Satellite communication
- Aircraft positioning
- Aircraft navigation
- Fiber-to-the-desktop
- Metro access rings
- Copper connection network
- Wireless teaching
- Car radio
- Pocket PC
