MAX241EEAI+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 28-SSOP (0.209, 5.30mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | TRISTATABLE RECEIVERS; EXTERNAL CHARGE PUMP |
| HTS Code | 8542.39.00.01 |
| Subcategory | Line Driver or Receivers |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX241 |
| Pin Count | 28 |
| JESD-30 Code | R-PDSO-G28 |
| Qualification Status | Not Qualified |
| Power Supplies | 5V |
| Supply Current-Max | 15mA |
| Data Rate | 120Kbps |
| Output Characteristics | 3-STATE |
| Differential Output | NO |
| Output Polarity | INVERTED |
| Protocol | RS232 |
| Input Characteristics | SCHMITT TRIGGER |
| Number of Drivers/Receivers | 4/5 |
| Driver Number of Bits | 4 |
| Receiver Number of Bits | 5 |
| Duplex | Full |
| Receiver Hysteresis | 500mV |
| Interface Standard | EIA-232-E; TIA-232-E; V.28 |
| Receive Delay-Max | 10000 ns |
| Output Low Current-Max | 0.0016A |
| Out Swing-Min | 10 V |
| Height Seated (Max) | 1.99mm |
| Length | 10.2mm |
| Width | 5.29mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX241EEAI+ Overview
The enhanced 28-SSOP (0.209, 5.30mm Width) package makes it an excellent LED driver.The package of this receiver is Tube.The Transceiver can transceiver technology has enabled this part to power many solutions for a variety of uses.Ideally, you should place this wide receiver on a Surface Mount-type PCB or development board.It takes 4.5V~5.5V from the power supply to run this differential driver.This electronic part can have?up to 4/5 eligible receivers/drivers on the field at once.?IC receiver has been designed primarily for applications operating at -40°C~85°C.Wide receiver can operate within the range of 5V supply voltages efficiently.For driving and receiving signals from data, this wide receiver has 28 terminations integrated.Transceiver comes with 28 standard pinouts that meet the market's requirements.Since the base part number MAX241 describes the product type, temperature, package, etc., you might get more options by searching with it.It provided a 4-bit resolution capability with this ic receiver.There is typically a resolution of 5 bits specified with this receiver.It is possible to subcategoriLine Driver or Receiverse this rf transceiver module as Line Driver or Receivers.It is designed to be operated from a 5V power supply, so the module isolated transceiver will work effectively.In addition, the optical transceiver module's TRISTATABLE RECEIVERS; EXTERNAL CHARGE PUMP function improves signal management accuracy and stability overall.Enough but no exceeding 15mA of input current should be supplied to the VCC pin of the ic receiver.
MAX241EEAI+ Features
Tube package
28 pin count
5V power supply
MAX241EEAI+ Applications
There are a lot of Maxim Integrated MAX241EEAI+ Drivers/Receivers/Transceivers applications.
- Changeing the frequency from IF to RF
- Remote controls
- Single fiber bidirectional application
- Metro access rings
- IPTV front end
- Structural bonding
- Clock radio
- Transmission stations
- Cordless telephone
- Car radio
