MAX242CWN+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 18-SOIC (0.295, 7.50mm Width) |
| Surface Mount | YES |
| Number of Pins | 18 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 18 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Matte Tin (Sn) |
| HTS Code | 8542.39.00.01 |
| Subcategory | Line Driver or Receivers |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX242 |
| Pin Count | 18 |
| Qualification Status | Not Qualified |
| Power Supplies | 5V |
| Supply Current-Max | 10mA |
| Data Rate | 200kbps |
| Output Characteristics | 3-STATE |
| Differential Output | NO |
| Output Polarity | INVERTED |
| Protocol | RS232 |
| Input Characteristics | SCHMITT TRIGGER |
| Number of Drivers/Receivers | 2/2 |
| Driver Number of Bits | 2 |
| Receiver Number of Bits | 2 |
| Duplex | Full |
| Receiver Hysteresis | 500mV |
| Interface Standard | EIA-232-E; TIA-232-E; V.28; V.24 |
| Receive Delay-Max | 1000 ns |
| Transmit Delay-Max | 3500 ns |
| Output Low Current-Max | 0.0032A |
| Out Swing-Min | 10 V |
| High Level Input Current-Max | 0.00004A |
| Height Seated (Max) | 2.65mm |
| Length | 11.55mm |
| Width | 7.5mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX242CWN+ Overview
This LED driver IC features an enhanced 18-SOIC (0.295, 7.50mm Width) package for driving common LEDs.Tube package is used for this receiver.This Transceiver can transceiver is a versatile part that has enabled many solutions to serve a variety of purposes.On any Surface Mount-type PCB or development board, you can install this wide receiver.This differential driver consumes 4.5V~5.5V for its power supplyAs many as 2/2 receivers/drivers are eligible for use on this electronic part.This ic receiver has been primarily designed for applications where the operating temperature is 0°C~70°C.An operating voltage range of 5V is suitable for this line driver ic.18 terminations are integrated into this wide receiver for driving and receiving signals from data.This transceiver is packaged with 18 market standard pinoutsMAX242 is the base part number for this part, and it identifies the product type, temperature, packaging, etc., so you can search for more variants with it.The driver IC has improved power dissipation control.It was possible to achieve a 2-bit resolution through this ic receiver.As a rule of thumb, this receiver is typically specified with a resolution of 2 bits.There is a subcategory named Line Driver or Receivers for this rf transceiver module.This driver IC is designed to operate from a 5V power supply.Ensure that the VCC pin of the ic receiver receives sufficient but not more than 10mA of input current.
MAX242CWN+ Features
Tube package
18 pin count
18 pins
5V power supply
MAX242CWN+ Applications
There are a lot of Maxim Integrated MAX242CWN+ Drivers/Receivers/Transceivers applications.
- Thermal management
- Pocket PC
- Cordless telephone
- Cable network front end
- Single fiber bidirectional application
- Transmission stations
- Wireless communication
- Structural bonding
- Indoor ad hoc meeting
- Wired telephone
