MAX250ESD+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 259.19969mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Line Driver or Receivers |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 255 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX250 |
| Pin Count | 14 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Interface | RS-232 |
| Operating Supply Current | 500μA |
| Supply Current-Max | 0.5mA |
| Data Rate | 116 kbps |
| Output Characteristics | 3-STATE |
| Differential Output | NO |
| Output Polarity | TRUE |
| Protocol | RS232 |
| Input Characteristics | SCHMITT TRIGGER |
| Number of Drivers/Receivers | 2/2 |
| Receiver Number of Bits | 2 |
| Duplex | Full |
| Receiver Hysteresis | 600mV |
| Number of Drivers | 2 |
| Number of Transceivers | 1 |
| Height | 1.55mm |
| Length | 8.74mm |
| Width | 4.013mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX250ESD+ Overview
The enhanced 14-SOIC (0.154, 3.90mm Width) package makes it an excellent LED driver.In the Tube package, this receiver is mounted.Since this is a Transceiver can transceiver, many solutions can use it for a variety of functions.A Surface Mount-type PCB or development board can be used to place this wide receiver.A differential driver like this uses 4.5V~5.5V of power.At any one time, this electronic part can have up to 2/2 eligible receivers/drivers.IC receiver is designed for applications with a temperature of -40°C~85°C.Driver ICs in this category can operate efficiently with a supply voltage range of 5V.14 terminations are integrated into this wide receiver for driving and receiving signals from data.In this package, you will find 14 market-standard pinouts for this transceiver.For more variants of this part, try searching with the base part number MAX250, which indicates the product type, temperature, package, etc.The driver IC has improved power dissipation control.Through optical transceiver downsizing and high-density Surface Mount mounting technologies, its package size is reduced dramatically.In the case of this receiver, a resolution of 2 bits is typically specified.There is a voltage input supply of 5V required for the operation of this integrated circuit.Line Driver or Receivers is a subcategory of this rf transceiver module.There is one driver IC that is designed to operate from a 5V power supply, and only one driver IC in total.In total, there are 1 transceivers implemented by this module isolated transceiver.The integrator circuit is embedded with 2 drivers.There should be enough current supplied to the VCC pin of the part, but not more than 0.5mA.An input voltage of 500μA is recommended for this integrating circuit to be able to drive LEDs.
MAX250ESD+ Features
Tube package
14 pin count
14 pins
5V power supply
MAX250ESD+ Applications
There are a lot of Maxim Integrated MAX250ESD+ Drivers/Receivers/Transceivers applications.
- Satellite communication
- Wireless projection application for conferences
- Satellite ground stations
- Changeing the frequency from IF to RF
- Wireless 3D game
- Automation systems
- Point-to-point networking
- Low power, low voltage systems
- Long-distance fiber optic network applications
- Indoor ad hoc meeting
