Parameters |
Factory Lead Time |
1 Week |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Surface Mount |
NO |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
1995 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Terminal Finish |
Matte Tin (Sn) |
Additional Feature |
ALSO OPERATE WITH 10V TO 30V SINGLE SUPPLY |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Position |
DUAL |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX303 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
JESD-30 Code |
R-PDIP-T16 |
Qualification Status |
Not Qualified |
Power Supplies |
5+-15V |
Number of Channels |
1 |
Number of Circuits |
2 |
Voltage - Supply, Single/Dual (±) |
10V~30V ±4.5V~20V |
Neg Supply Voltage-Nom (Vsup) |
-15V |
On-State Resistance (Max) |
35Ohm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
72 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
12pF 12pF |
On-state Resistance Match-Nom |
0.5Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
150ns, 100ns |
Charge Injection |
10pC |
Channel-to-Channel Matching (ΔRon) |
500m Ω |
Crosstalk |
-90dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
150ns |
Switch-off Time-Max |
100ns |
Length |
19.175mm |
RoHS Status |
ROHS3 Compliant |
MAX303CPE+ Overview
As the electronic part is packed in 16-DIP (0.300, 7.62mm), international shipping is convenient. This packaging method provides high reliability because it uses advanced packaging techniques. Through Hole is where this multiplexer is located. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Operation at a temperature around 0°C~70°C TA. In total, there have been 16 terminations. Due to its 1 channels, the electrical component produces high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. A total of 16 pins are injected into the electrical part body. Circuits based on SPDT switching are used to construct these analog switch ics. The multiplexer consists of 2 circuits. Use MAX303 to search for variants of the digital switches. Multiplexer or Switches is a typical switch device. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. There is also ALSO OPERATE WITH 10V TO 30V SINGLE SUPPLY to look out for in this electronic part.
MAX303CPE+ Features
1 Channels
Switch Circuit: SPDT
Additional Features: ALSO OPERATE WITH 10V TO 30V SINGLE SUPPLY
MAX303CPE+ Applications
There are a lot of Maxim Integrated MAX303CPE+ Analog Switches & Multiplexers ICs applications.
- Medical Instrumentation
- Cell phones
- Power routing
- Cross Connects
- Automatic test equipment
- Voice over IP/DSL – Integrated Access Devices, Smart
- DSUs
- USB 1.1 signal switching circuits
- PBX interfaces
- Intelligent PBX