Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
1995 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
35Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
696mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX303 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
20V |
Power Supplies |
5+-15V |
Number of Channels |
2 |
Max Supply Voltage |
30V |
Min Supply Voltage |
10V |
Nominal Supply Current |
10nA |
Max Supply Current |
10nA |
Turn On Delay Time |
150 ns |
Voltage - Supply, Single/Dual (±) |
10V~30V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
100 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
35Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
72 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
12pF 12pF |
On-state Resistance Match-Nom |
0.5Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
150ns, 100ns |
Charge Injection |
10pC |
Channel-to-Channel Matching (ΔRon) |
500m Ω |
Crosstalk |
-90dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Height |
1.5mm |
Length |
10mm |
Width |
4mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
MAX303CSE+ Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. In order to provide high reliability, an advanced packaging method Tube is used. The multiplexer is located in Surface Mount. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Around 0°C~70°C TA is the extended operating temperature. A total of 16 terminations have been recorded. The electronic part provides high-quality output because it has 2 channels. With a 15V voltage supply, the electrical component should be turned on and run. It is part of the design of the 16 series that this electronic component is included. On the other hand, analog switches can be constructed using SPDT switching circuits. Try searching for MAX303 variants of the analog switch ic. This digital multiplexer has 35Ohm internal resistance. To find out what the 16 pins do, please refer to the datasheets. Multiplexer or Switches is a typical switch device. It is normally recommended that users do not supply the multiplexer with voltages higher than 30V. A cost-effective Dual, Single supply type analogue multiplexer. It is recommended that the electrical component receives a voltage of 10V. If put voltage greater than 10nA on the device, damage may be caused to the analogue multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. If you are using dual power supplies, you should attach at least 4.5V. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. 20V operating voltages can be used with this electrical part.
MAX303CSE+ Features
2 Channels
Switch Circuit: SPDT
MAX303CSE+ Applications
There are a lot of Maxim Integrated MAX303CSE+ Analog Switches & Multiplexers ICs applications.
- High speed data transmission line cards
- Communication systems
- DSLAMs
- Remote wireless modules
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- ISDN NT1/TA
- Audio and video switching
- E1 Network Equipment
- SDH
- PBXs