Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tape & Reel (TR) |
Published |
1995 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
35Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
842mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX303 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
20V |
Power Supplies |
5+-15V |
Number of Channels |
1 |
Number of Circuits |
2 |
Max Supply Voltage |
30V |
Min Supply Voltage |
10V |
Nominal Supply Current |
10nA |
Max Supply Current |
10nA |
Turn On Delay Time |
150 ns |
Voltage - Supply, Single/Dual (±) |
10V~30V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
100 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
35Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
72 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
12pF 12pF |
On-state Resistance Match-Nom |
0.5Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
150ns, 100ns |
Charge Injection |
10pC |
Channel-to-Channel Matching (ΔRon) |
500m Ω |
Crosstalk |
-90dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
MAX303CSE+T Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Operating temperature around 0°C~70°C TA extended. A total of 16 terminations have been recorded. A electrical component with 1 channels is capable of high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. It is injected into the electrical part body with 16 pins. The analog switch ics are built using SPDT switching circuits. A total of 2 circuits make up this switch device. Using the MAX303 search parameter, you can discover variants of the switch. An switch multiplexer with 35Ohm internal resistance has a value of 35Ohm. Datasheets for 16 pin functions are available upon request. Theswitch device is a typical Multiplexer or Switches. A voltage higher than 30V should not normally be supplied to the switches. Analog switch ics with Dual, Single supply type are cost-effective. There should be 10V voltage fed to the electrical part below 10V. If put voltage greater than 10nA on the device, damage may be caused to the analogue multiplexer. There is no problem with using dual supply voltage, but it should not exceed 20V. In the case of dual power supplies, you should connect at least 4.5V. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. A voltage of 20V can be used to operate the electronic component.
MAX303CSE+T Features
1 Channels
Switch Circuit: SPDT
MAX303CSE+T Applications
There are a lot of Maxim Integrated MAX303CSE+T Analog Switches & Multiplexers ICs applications.
- High reliability control systems
- Wireless Local Loop
- Medical
- ATM
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Power routing
- Automotive applications
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- E1 Network Equipment
- MP3 players